Pelco SD5TAC - Manuals - manualsarea.com

Page 2 - CONTENTS; Section

2 Pelco Manual C2422M (5/00) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 OPERATION ...................................................................................................................... 4 POWER-UP DISPLAY ...

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; MEASURES DE SECURITE IMPORTANTES

Pelco Manual C2422M (5/00) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specifically ...

Page 4 - OPERATION; HOW TO OPERATE YOUR SPECTRA LITE DOME; Protocol C

4 Pelco Manual C2422M (5/00) OPERATION POWER-UP DISPLAY When the Spectra Lite™ dome is powered up, the selected protocol, revision number, andother information is displayed on the monitor. For example, the screen might show thefollowing information: The information displayed depends on the selectedp...

Page 6 - PROGRAMMING; Programming Guide - Spectra Lite; MAIN MENU; For detailed instructions, refer to the following sections.

6 Pelco Manual C2422M (5/00) PROGRAMMING Programming Guide - Spectra Lite 1. Access main menu (preset 95). 2. Make main menu selections.Joystick: Move up or down to position cursor orto toggle between selections. Iris Open: EnterIris Close: Cancel PRESETS The following presets arereserved for specia...

Page 9 - AUTO IRIS; The following are the settings for auto iris:

Pelco Manual C2422M (5/00) 9 AUTO IRIS The following are the settings for auto iris: ModeLevel To change the settings for auto iris:1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the c...

Page 11 - Programming

Pelco Manual C2422M (5/00) 11 GAIN The gain adjusts the signal level of the video output. Increasing the gain in low lightconditions will increase the level of noise in the picture. To change the gain:1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. P...

Page 12 - Scan Limit Stops; Make sure limit stops are turned ON, and then exit the menu.; LINE SYNCHRONIZATION

12 Pelco Manual C2422M (5/00) Main Menu <Camera><Line Sync><Power Up><Other>EXIT Line Sync Menu Line sync On Line sync phase 0 Exit Scan Limit Stops Refer to the documentation for your control system for programming presets, and then dothe following:1. Make sure limit stops a...

Page 13 - PARK TIME MINUTES; Preset 1 must be; The default setting is Default.

Pelco Manual C2422M (5/00) 13 PARK TIME MINUTES This feature causes the dome to park at preset 1 after a programmed number of minutes ofcontrol inactivity. The time can be set from 1 minute to 720 minutes (12 hours), or it can be setto zero, which disables this feature. To change the park time:1. Pr...

Page 14 - RESET CAMERA

14 Pelco Manual C2422M (5/00) RESET CAMERA Main Menu <Camera><Line Sync><Power Up><Other>EXIT Camera Menu Backlight comp Off Reset camera<Gain/AGC><Auto-iris><Next>Exit Resetting the camera returns the settings to their defaults. Default Settings Backlight c...

Page 15 - SCAN SPEED; SHARPNESS; Do the following to manually adjust the sharpness of the picture:

Pelco Manual C2422M (5/00) 15 SCAN SPEED Next Menu Shutter speed Auto Auto focus mode Auto <Sharpness><White balance>Prev (back to prev. menu)Exit Main Menu <Camera><Line Sync><Power Up><Other>EXIT Main Menu <Camera><Line Sync><Power Up><Other...

Page 16 - SHUTTER SPEED; There are several shutter speed settings:

16 Pelco Manual C2422M (5/00) SHUTTER SPEED Next Menu Shutter speed Auto Auto focus mode Auto<Sharpness><White balance>Prev (back to prev. menu)Exit Main Menu <Camera><Line Sync><Power Up><Other>EXIT Camera Menu Backlight comp Off Reset camera<Gain/AGC><A...

Page 17 - WHITE BALANCE

Pelco Manual C2422M (5/00) 17 Next Menu Shutter speed Auto Auto focus mode Auto <Sharpness><White balance>Prev (back to prev. menu)Exit Main Menu <Camera><Line Sync><Power Up><Other>EXIT Camera Menu Backlight comp Off Reset camera<Gain/AGC><Auto-iris>&...

Page 18 - MAINTENANCE; DOME CLEANING; SERVICE MANUAL

18 Pelco Manual C2422M (5/00) MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch thesurfaces of the dome. Exterior Surface - Clean the dome’s exterior surface with a nonabrasive cleaning cloth andcleaning agent that is safe for acryli...

Page 19 - SPECIFICATIONS; MECHANICAL

Pelco Manual C2422M (5/00) 19 SPECIFICATIONS MECHANICAL Pan Movement: 360 ° continuous pan rotation Vertical Tilt: Unobstructed +2 ° to -92 ° Manual Pan/Tilt Speeds* Pan: 0.5 ° -80 ° /sec manual operation, 150 ° /sec turbo Tilt: 0.5 ° -40 ° /sec Preset Speeds Pan: 250 ° /sec Tilt: 200 ° /sec * For v...

Page 20 - REVISION HISTORY; PRODUCT WARRANTY AND RETURN INFORMATION

20 Pelco Manual C2422M (5/00) Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. © Copyright 2000, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved. U.S. Patent No. 5,931,432. REVISION HISTORY Manual # Date Comments C2422M 5...