Pelco PT7700 - Manuals - manualsarea.com

Page 3 - CONTENTS; REVISION HISTORY; Original version

2 Pelco Manual C397M (4/98) LIST OF ILLUSTRATIONS Figure Page 1 PT7700 Series Input Wiring Diagram ................................................ 8 2 PT7700 Series Connector ................................................................. 9 3 Tilt Limit Stop Adjustment ..............................

Page 4 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C397M (4/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and s...

Page 5 - Agency Compliance Certification

4 Pelco Manual C397M (4/98) 2.0 DESCRIPTION The PT7700 systems combine an environmental camera enclosure, pan/tilt as-sembly, and receiver/driver into a single unit that you can install indoors or out-doors. You can install 2/3-inch (1.69 cm) and 1-inch (2.54 cm) format cameras witheither fixed foca...

Page 7 - If the AC power input to your

6 Pelco Manual C397M (4/98) j. On the bottom of the enclosure, remove the vent grill and filters at thefront of the enclosure. Replace the grill with one of the vent cover platesthat was attached to the camera sled as loose equipment. k. On the bottom of the enclosure, attach the other vent cover pl...

Page 8 - Proceed to Section 3.4, TESTING SYSTEM AND ADJUSTING LIMIT STOPS.

Pelco Manual C397M (4/98) 7 3.3 WIRING 1. Route the six-foot power/video/control cable through the wall or pedestal mountif applicable. 2. Connect the end of the cable with the 16-pin connector to the mating connec-tor in the base of the pan/tilt unit. 3. Connect the other end of the cable as follow...

Page 9 - PT7700 Series Input Wiring Diagram

8 Pelco Manual C397M (4/98) Figure 1. PT7700 Series Input Wiring Diagram

Page 11 - TESTING SYSTEM AND ADJUSTING LIMIT STOPS; Never remove; . Tilt Limit Stop Adjustment

10 Pelco Manual C397M (4/98) 3.4 TESTING SYSTEM AND ADJUSTING LIMIT STOPS To test the system and adjust the limit stops: 1. Loosen the two pan limit stops at the base of the pan/tilt. 2. Turn on power. 3. Test the system by moving the pan/tilt to the left, right, up and down. Do notmove the pan/tilt...

Page 12 - C) and to turn them off

Pelco Manual C397M (4/98) 11 4.0 OPERATION Refer to the manual for your control equipment for operating the pan/tilt system. If your enclosure has a thermostatically controlled blower, the thermostat is set toturn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off be- tween...

Page 15 - Tilt Adjustments and Lubrication; Pan Adjustments and Lubrication

14 Pelco Manual C397M (4/98) Tilt Adjustments and Lubrication 10. Remove the plastic cover on the right side of the pan/tilt unit. 11. Refer to Figure 5. Verify that the worm (B) is fully seated in the worm gear (A).If it is not, turn the two nuts (C) to lift the worm. Tighten the two nuts at (D). 1...

Page 16 - EXPLODED ASSEMBLY DIAGRAMS; Exploded Assembly Diagram for Blower and Circuit Board

Pelco Manual C397M (4/98) 15 7.0 EXPLODED ASSEMBLY DIAGRAMS Figure 6. Exploded Assembly Diagram for Blower and Circuit Board SCREWS COME WITHBLANKING PLATE 2 1 4 5 6 7 F G H 12 8 B A B E 9 A B C 10 C 11 B

Page 18 - Exploded Assembly Diagram for Heaters and Circuit Board

Pelco Manual C397M (4/98) 17 Figure 7. Exploded Assembly Diagram for Heaters and Circuit Board Table B. Parts List (Figure 7) Item Qty Description Part Number 1 1 Bracket/Heater Sink 57004020COMP 2 2 Heater, 230 VAC HTR40220 2 Heater, 120 VAC HTR50120 3 1 Connector Plug CON1-480424-0 4 1 Power Suppl...

Page 19 - Wiring Diagram for Enclosure Circuit Board

18 Pelco Manual C397M (4/98) Figure 8. Wiring Diagram for Enclosure Circuit Board

Page 21 - SYSTEM; Unit Weight

20 Pelco Manual C397M (4/98) 8.0 SPECIFICATIONS SYSTEM Input Voltage: 120 or 230 VAC, 50/60 Hz Power Requirements: PT7729RX,PT7729WX 0.35 A (42 vA) PT7729RX-1,PT7723RX-1,PT7729RX-1/PP,PT7729RX-1/SL,PT7729WX-1,PT7723WX-1 1.7 A (204 vA) PT7729RX-3,PT7729RX-3/PP,PT7729WX-3 1.9 A (437 vA) Power/Control ...

Page 22 - Coaxitron

Pelco Manual C397M (4/98) 21 PAN/TILT Construction Body: Aluminum plate Side Covers: Vacuum-formed ABS plastic, UV protected Pan: 0-355 ° movement in horizontal plane, except PT7729RX-1/SL, which has 360 ° pan rotation Pan Speed: 9 ° /sec ± 1 ° (no load condition) Tilt: +15 ° movement in vertical pl...

Page 23 - Wiretron Receiver/Driver; 5 mA current loop; ENCLOSURE; Aluminum

22 Pelco Manual C397M (4/98) Wiretron Receiver/Driver Fuses: One 1 A, 3 AG typeTwo 2/10 A, 3 AG type Control Method: 15 pulse train (pulse width modulated) Pulse Amplitude: 35 mA current loop CableRequirements: Twisted pair, unshielded Operating Distance: 22 AWG - 5 miles (8 km) 20 AWG - 10 miles (1...

Page 25 - WARRANTY AND RETURN INFORMATION; WARRANTY

24 Pelco Manual C397M (4/98) 9.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, with...