Pelco PT506-24A - Manuals - manualsarea.com

Page 2 - ii; CONTENTS; Section

18 Pelco Manual C580M Rev D (9/97) ii CONTENTS Section Page 1.0 GENERAL .................................................................................................. 1 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 1 2.0 DESCRIPTION ..........................................

Page 3 - LIST OF ILLUSTRATIONS; Figure; LIST OF TABLES; Table; iii

Pelco Manual C580M Rev D (9/97) 19 LIST OF ILLUSTRATIONS Figure Page 1 PT506-24DT Basic System Configuration ......................................... 3 2 PT506-24DT Configured with PT506-24A ......................................... 4 3 PT506-24DT Configured with a Relay Box ..........................

Page 4 - iv

20 Pelco Manual C580M Rev D (9/97) (This page intentionally left blank.) iv

Page 5 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C580M Rev D (9/97) 1 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation...

Page 7 - RECOMMENDED CABLE DISTANCES; Wire Size; PT506-24DT Basic System Configuration

Pelco Manual C580M Rev D (9/97) 3 3.0 INSTALLATION Figure 1 shows a typical rear panel installation of the PT506-24DT controller. Thedistance from the controller is limited by the wire size and pan/tilt used. (See Sec-tion 3.1 Recommended Cable Distances.) Figure 2 shows a typical rear panel install...

Page 8 - PT506-24DT Configured with a Relay Box

4 Pelco Manual C580M Rev D (9/97) Figure 2. PT506-24DT Configured with PT506-24A Figure 3. PT506-24DT Configured with a Relay Box

Page 9 - CONNECTOR ASSEMBLY; Prepare the wires from the conductor cable as follows:; Connector Assembly; OR

Pelco Manual C580M Rev D (9/97) 5 3.2 CONNECTOR ASSEMBLY Assemble the connector parts according to the instructions below. Detail B, below,reflects the pin arrangement specific to all PT506-24DT Pan/Tilt and Lens Controland the PT506-24A Auto/Random Scan Control. Refer to Figure 4 during assembly.Fo...

Page 10 - Select another station and repeat steps 1 through 8.

6 Pelco Manual C580M Rev D (9/97) 4.0 OPERATION The PT506-24DT will not allow control of any of the six pan/tilt stations until one isselected by pressing the desired station on the latching selection switches. Once aselection has been made, the switch will illuminate and all control functions will ...

Page 11 - Pressing “AUTO/RANDOM”; CONTINUOUS AUTO SCAN; PT506-24A Duty Cycle Combinations; DUTY CYCLE

Pelco Manual C580M Rev D (9/97) 7 4.2 OPERATIONAL TEST — PT506-24A The PT506-24A will add two modes of automatic pan operation to the PT506-24DT.Once the PT506-24A is interconnected as shown in Figure 2, apply power to theunits. When the corresponding paddle switch to the station selected is in the ...

Page 19 - GENERAL

Pelco Manual C580M Rev D (9/97) 15 GENERAL Enclosure Construction Panel: Aluminum Cover: Steel, textured black enamel Chassis: Steel, galvanized TemperatureRange: 32 ° to 120 ° F (0 ° to 50 ° C) Size: See Figure 6 Weight PT506-24DT 13 lbs 6 oz (6 kg) PT506-24A 18 lbs (8.1 kg) Shipping Weight PT506-2...

Page 20 - WARRANTY AND RETURN INFORMATION; WARRANTY

16 Pelco Manual C580M Rev D (9/97) 8.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1997, Pelco. All rights reserved. WARRANTY Pelco will repair or replace...