Pelco PMCQ14A - Manuals

Pelco PMCQ14A – Manual in PDF format online.

Manuals:

Manual

Manual Pelco PMCQ14A

Summary

Page 2 - CONTENTS; LIST OF ILLUSTRATIONS

2 Pelco Manual C1970M-A (7/01) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3DESCRIPTION ................................................................................................................... 4 FEATURES ...........

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; may violate

Pelco Manual C1970M-A (7/01) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specificall...

Page 4 - DESCRIPTION; FEATURES

4 Pelco Manual C1970M-A (7/01) DESCRIPTION FEATURES • Observe up to Four Camera Images at Once or in Sequence • Programmable Dwell Time for Each Camera During Sequence Mode • Picture-In-Picture (PIP) View in Horizontal or Vertical Format • 2X Digital Zoom and Freeze Functions • Alarm Inputs for Each...

Page 5 - Figure 1. Typical Application Using PMCQ14A Monitor; Figure 2. Examples of Camera Locations

Pelco Manual C1970M-A (7/01) 5 Figure 1. Typical Application Using PMCQ14A Monitor EH3500 IMAGEPAK OUTDOOR W/ HEATER & DEFROSTER WCS1-4 POWER SUPPLY EH100 IMAGEPAK INDOOR MCS4-2 POWER SUPPLY24 VAC TO ALL INDOOR CAMERAS DF5 PENDANT DOMEPAK INDOOR DF5 IN-CEILING DOMEPAK INDOOR TLR2024 VIDEO CASSET...

Page 6 - INSTALLATION; Test according to the check-out procedure in Table B.; Figure 3. Monitor Connections

6 Pelco Manual C1970M-A (7/01) INSTALLATION 1. Place monitor on a stable surfacesuch as a shelf or desk top. 2. Connect cameras or alternate videosources to the desired channelIN/OUT connectors on the back ofthe monitor (refer to Figure 3). 3. Set impedance switches to the75-ohm position (refer to F...

Page 7 - PROGRAMMING; Figure 4. Control Locations on Front of Monitor; Press ALT + MENU to toggle in or out of the programming menu.; NOTE: The date field does not change in the Setup Menu

Pelco Manual C1970M-A (7/01) 7 PROGRAMMING QUAD MENU CH4 VCR PIP SEQ CH3 ZOOM FREEZE CH2 RESET ALT CH1 TALK AUDIO MIC TINT SHARP COLOR BRIGHT CONTRAST VOLUME POWER FRONT PANEL PROGRAMING BUTTONS RETURNS TO DEFAULT (ALT+MENU ENTERS/EXITS SETUP MENU) Figure 4. Control Locations on Front of Monitor Tab...

Page 8 - DISPLAY; Table C. Display Functions

8 Pelco Manual C1970M-A (7/01) CHECK OUT Table B. Check-Out Procedure This procedure assumes that power is on. Step Procedure Results 1 Calibrate cameras. Follow the manufacturer’s recommendations for calibration. 2 Press the QUAD/MENU button. See quad display. 3 Press the CH 1 button. See channel 1...

Page 9 - Figure 5. Display Selections; QUAD MODE

Pelco Manual C1970M-A (7/01) 9 Figure 5. Display Selections PIP MODE (HORZ) QUAD MODE SEQUENCE MODE PIP SEQ QUAD MENU SINGLE-CAMERA MODE CH4 VCR MENU MODE CH4 VCR CH3 ZOOM FREEZE CH2 CH1 TALK AUDIO MIC TINT SHARP COLOR BRIGHT CONTRAST VOLUME POWER PIP SEQ QUAD MENU RESET ALT PIP SEQ RESET ALT QUAD M...

Page 10 - INTERCOM; The intercom; Figure 6. Intercom Activities on Screen; Table D. Intercom Function; Action; Listen channel X; You can operate the intercom when the other display

10 Pelco Manual C1970M-A (7/01) INTERCOM The intercom operates with one camera at a time. When the monitor is in quad displaymode, a speaker icon appears next to the channel number to show which camera has theintercom active. NOTE: The intercom function is available onlywhen CCQ1400A-4cameras are us...

Page 11 - ALARM; Figure 7. Alarm Activities on Screen; Alarm Function

Pelco Manual C1970M-A (7/01) 11 ALARM The alarm operates with any or all cameras at once. ALM flashes at the top center of thescreen and the display automatically switches to show the camera that has the alarm. Figure 7. Alarm Activities on Screen Table E. Alarm Function Alarm Function Action Alarm ...

Page 12 - Reference

12 Pelco Manual C1970M-A (7/01) Figure 8. Monitor Back Panel Controls and Connections Table F. Back Panel Reference Key Reference Number Description Function 1 Power inlet Accepts 110 to 240 Volts AC, 50/60 Hz power. 2 Main power switch Controls power to monitor and cameras. 3 75-ohm/High impedance ...

Page 14 - TECHNICAL SPECIFICATIONS; ELECTRICAL

14 Pelco Manual C1970M-A (7/01) TECHNICAL SPECIFICATIONS ELECTRICAL Input Voltage: 100 to 240 VAC, 50/60 Hz Power Consumption: 70 watts Signal Format: NTSC Scanning System: 2:1 interlace Picture Elements: 512 (H) x 492 (V) Horizontal Resolution: 350 TV lines (center) Linearity: Less than 12% Audio O...

Page 15 - ENVIRONMENTAL; REGULATORY NOTICES

Pelco Manual C1970M-A (7/01) 15 ENVIRONMENTAL OperatingTemperature: 32 ° to 104 ° F (0 ° to 40 ° C) StorageTemperature: 4 ° to 158 ° F (-20 ° to 70 ° C) Humidity: 35% to 80%, non-condensing (Design and product specifications subject to change without notice.) REGULATORY NOTICES Note: This equipment ...

Page 16 - REVISION HISTORY; Date; PRODUCT WARRANTY AND RETURN INFORMATION

16 Pelco Manual C1970M-A (7/01) REVISION HISTORY Manual # Date Comments C1970M 7/00 Original version. C1970M-A 7/01 Date and time programming revised. Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2001, Pelco. Endura and ExSite a...