Pelco Not ICS110-CW - Manuals

6 C3406M-D (1/07) Description The ICS110-CW Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor application...

C3406M-D (1/07) 7 Figure 1. Package Components COVER AND BACK BOX (1) CAMERA MODULE (1) TRIM RING, DOME LINER, AND CLEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-INCH HOLLOW SCREWDRIVER BIT (1) BLACK PLUG (1) SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 0.75-INCH PHILLIPS PAN HEAD SCREWS...

8 C3406M-D (1/07) Cover and Back Box Installation The ICS110-CW Series Camclosure integrated camera system mounts only to a surface. It can be wired through the cover into a surface, electrical box, or plaster ring. You can also wire it through a side conduit. UNSHIELDED TWISTED PAIR (UTP) VIDEO The...

C3406M-D (1/07) 9 8. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box ...

C3406M-D (1/07) 11 404 PLASTER RING INSTALLATION NOTE: You should install the camera module into the back box before installing the back box into the cover. When installing the back box into the cover, rotate the camera module to access the mounting holes. Refer to Camera Module on page 14 for more ...

12 C3406M-D (1/07) 5. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box...

14 C3406M-D (1/07) Camera Module The ICS110-CW Series Camclosure camera module includes the camera, camera bracket, and heater board. To perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module. MODULE REM...

16 C3406M-D (1/07) CAMERA ORIENTATION At the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image will be upside down. To change the camera orientation (refer to Figure 8): 1. Remove the camera module from the bac...

C3406M-D (1/07) 17 Camera Adjustments To perform the following camera adjustments, make sure to plug in the camera and service connectors. You may have to remove the camera module from the back box. Connect a monitor. Then turn on power to the camera and monitor. To use the service connector, refer ...

18 C3406M-D (1/07) SWITCH SETTINGS Locate the DIP switch (refer to Figure 10). Then set the switches for your installation. Figure 10. DIP Switch SW1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW2: Line Sync Set to ON to use AC line lock. Set to OFF for internal line sy...

C3406M-D (1/07) 19 Extended dynamic range: Use for extremely high dynamic installations, for example, doorways, entrances, and exits. This profile offers the maximum wide dynamic range. Fluorescent: Use for any installation with flickering lighting of any kind. NOTE: If you select the Fluorescent pr...

20 C3406M-D (1/07) Camera Positioning Manually rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis in Figure 12). NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in damage to the wiring. Figure 12. Positioning...

C3406M-D (1/07) 21 Install Dome and Trim Ring 1. Adjust the dome liner if installed (refer to Figure 13): a. Align the screw holes in the trim ring with those in the back box to identify the proper dome liner position. b. Loosen the three Phillips screws located in the trim ring. c. Insert the blade...

24 C3406M-D (1/07) Specifications CAMERA Imaging Device 1/3-inch imager Dynamic Range 102 dB typical/120 dB maximum Picture Elements Sensor resolution: 742 (H) x 552 (V) Signal System NTSC or PAL Scanning System 2:1 interlace/progressive Synchronization Internal/AC line lock Horizontal Resolution Mo...

C3406M-D (1/07) 25 BACKBOX Electrical Input Voltage** 12 VDC or 24 VAC (±10%), autosensing Power Consumption 10 watts or less Video Connector Composite: BNCUTP: Twisted pair General Pan/Tilt Adjustment Manual Pan 360° Tilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera...

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic ...