Pelco NET5400T - Manuals

6 C4658M-C (6/10) Important Notices LEGAL NOTICE SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTI...

C4658M-C (6/10) 7 Video Quality Caution FRAME RATE NOTICE REGARDING USER-SELECTED OPTIONS Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be used in lower quality modes, which can degrade picture quality, to allow for a slower ra...

8 C4658M-C (6/10) Description The NET5400T Series video encoder is a network-based multichannel encoder with a built-in, Web-based viewer for live streaming to a standard Web browser (Microsoft ® Internet Explorer ® or Mozilla ® Firefox ® ). The encoder features open architecture connectivity and is...

10 C4658M-C (6/10) Before You Begin Endura is a network system that requires a continuous amount of bandwidth to transmit true, live video; therefore, always include your network administrator when planning and installing Endura components. You will also need the following items: • Pelco-approved En...

C4658M-C (6/10) 11 PACKAGE CONTENTS The following diagram shows the box contents. When installing the unit, refer to this diagram. Figure 1. Package Contents NOTE: Since power requirements vary by installation, the NET5400T Series does not include an individual power supply. You can purchase either ...

12 C4658M-C (6/10) PRODUCT SERIAL NUMBER LABEL PLACEMENT Product serial number labels help Pelco’s Product Support identify your system and its factory configuration in case the unit or its components require service. A label citing your product’s serial number is attached to the bottom panel of the...

C4658M-C (6/10) 13 Equipment Placement and Rack Mounting Use one of the following installation methods for the unit: • Place the unit on a flat surface, such as a shelf or desktop. • Mount the unit to a wall using the optional WM5002-4U wall mount kit. • Install the unit in the optional RK5200PS-5U ...

14 C4658M-C (6/10) 2. Position the unit to allow for cable and power cord clearance at the front and rear panels. Figure 4. Desktop Placement WALL MOUNTING A single NET5400T Series unit can be mounted to a wall using the optional WM5002-4U wall mount system. To mount the unit to a wall using the WM5...

C4658M-C (6/10) 15 3. Tighten the thumbscrew on the wall mount to secure the unit. Figure 6. Tighten the Thumbscrew to Secure the Unit RACK MOUNTING The optional RK5200PS-5U rack mount kit can support up to 12 NET5400T Series units. Each unit connects directly to a power connector in the rack and is...

C4658M-C (6/10) 17 PELCO BADGE ORIENTATION The Pelco badge on the front panel of the unit can be rotated in quarter turns. If you install the unit on a flat surface, the Pelco badge will be turned the wrong way. To rotate the Pelco badge: 1. Use the Pelco badge rotation sticker that came with the un...

18 C4658M-C (6/10) Connections 4-CHANNEL MODELS Familiarize yourself with the rear panel before connecting any equipment to the unit. Refer to Connecting a PTZ Device, Relay, and Alarms on page 24 for a description of the terminal block connections. Figure 10. Rear Panel for 4-Channel Models ì 4-Pin...

C4658M-C (6/10) 21 CONNECTING VIDEO INPUT AND OUTPUT DEVICES The NET5400T Series offers both analog video input and looping video output (available on the 1-channel models). Figure 13. Video Input and Output Before installing the unit, make sure the distance from the unit to the video device is less...

C4658M-C (6/10) 23 CONNECTING AUDIO The NET5400T Series supports one audio line input for an amplified audio input device. The unit encodes audio and video signals simultaneously. This lets you listen to activity in the target area. Figure 14. Audio Connections To connect an audio input device: 1. W...

24 C4658M-C (6/10) CONNECTING A PTZ DEVICE, RELAY, AND ALARMS The NET5400T Series incorporates a 16-pin terminal block to support the following items: • PTZ device, such as a dome camera, using the Pelco D protocol (RS-422) • Relay control, either normally open (N.O.) or normally closed (N.C.) • Up ...

26 C4658M-C (6/10) Figure 16. Connecting a Spectra Dome Refer to Table C when installing the PTZ device. It lists the serial port settings that the unit supports. NOTE: When using 115200 as the data rate, the following additional settings are used: the Data Bit is set to 8, Parity is set to No Flow ...

C4658M-C (6/10) 27 CONNECTING A RELAY DEVICE The NET4500T has an output for triggering an external device. It supports both momentary and continuous relay operation. You can operate the relay interactively, during an active connection, or automatically to coincide with certain events. Typical applic...

28 C4658M-C (6/10) CONNECTING ALARMS The NET5400T Series offers three alarm inputs for external signaling devices, such as door contacts or motion detectors. Each encoder supports both normally open and normally closed devices. Each encoder also supports both supervised and unsupervised alarms. Once...

C4658M-C (6/10) 29 Figure 19 illustrates the wiring configuration for supervised alarm inputs. Figure 19. Supervised Alarm Input Wiring Unsupervised Alarms When an alarm is configured as an unsupervised alarm, the unit only triggers an alarm when the normal alarm state (open or closed) changes. Figu...

30 C4658M-C (6/10) Figure 21 illustrates the wiring configuration for unsupervised alarm inputs. Figure 21. Unsupervised Alarm Input Wiring Alarm Connections Figure 22 shows how to wire the video encoder to an alarm (refer to Table B on page 25 for the specific connector pin assignments). Figure 22....

C4658M-C (6/10) 31 CONNECTING TO THE NETWORK Connect the video encoder to the Endura network: 1. Connect a Cat5e (or better) cable to either network port on the front panel. NOTE: If you are using a PoE or PoE+ , no other Cat5e is required. Using both network ports creates a video loop in the networ...

32 C4658M-C (6/10) DAISY-CHAINING SEVERAL UNITS A maximum of four NET5400T Series units can be connected together in a daisy-chained network. Follow these guidelines when setting up the daisy chain: • Always use Cat6 cable with strain relief included at each connector. • Always follow the cable leng...

C4658M-C (6/10) 33 CONNECTING POWER This product is intended to be supplied with power by a 12 VDC (except for the NET5404T), 24 VAC, or a PoE power supply that is UL Listed, Class 2, or a UL Listed ITE power supply marked LPS, such as Pelco's NET5200PS or RK5200PS-5U. One- and two-channel models ca...

C4658M-C (6/10) 35 FRONT PANEL INDICATORS Refer to the NET5400T Series Configuration manual for details on setting up any camera that is attached to the unit. You can also view video from cameras attached to the unit from the WS5200 software or from the VCD5200 video console display. 4-CHANNEL MODEL...

C4658M-C (6/10) 37 DESCRIPTIONS OF THE FRONT PANEL INDICATORS Video presence Video presence is indicated by one of the following conditions: • Not Lit: A camera has not been connected yet. • Green: Camera video is present at the video in connector. • Red: Video is no longer present; the camera is no...

38 C4658M-C (6/10) Troubleshooting If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or 1-559-292-1981 (international) for assistance. Access the properties windows for the NET5400T Series video encoder on the Endura workstatio...

40 C4658M-C (6/10) Specifications SYSTEM Operating System Linux ® User Interface Remote operation from WS5070, WS5200 software, or VCD5200; Web-based remote operation is also available VIDEO/AUDIO Video Standards NTSC/PAL/EIA/CCIR composite Video Coding H.264 high, medium, or low profiles Video Stre...

C4658M-C (6/10) 41 VIDEO ACTIVITY DETECTION Zones 3 plus 1 background zone Zone Types Any shape, user-definable in 16 x 16 pixel blocks Sensitivity/Threshold Adjustable per zone AUXILIARY INTERFACES Serial Pelco D protocols (RS-422); uses 4 of 16 pins on terminal block connector Terminal Block Conne...

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years: – Fiber optic products– Unshiel...