Pelco MRD1400HZ16 - Manuals

Page 2 - LIST OF TABLES; CONTENTS; LIST OF ILLUSTRATONS

2 Pelco Manual C1973M-B (8/03) LIST OF TABLES Table Page A Baud Rate Switch Settings ................................................................................ 4 B MRD DIP Switch Settings .................................................................................. 5 C Two-Wire Control Co...

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; The product and/or manual may bear the following marks:

Pelco Manual C1973M-B (8/03) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and con-form to all local codes. 2. There are no user-serviceabl...

Page 4 - Item; DIP SWITCH SETTINGS; SW-1 Default Switch Settings; Baud; Baud Rate Switch Settings; Switch Setting

4 Pelco Manual C1973M-B (8/03) DESCRIPTION The MRD1400HZ16 is a camera interface control for Pelco’s CC1400HZ16 Series digitalcolor camera. The unit can be mounted directly to a wall or installed in a DF5 Series dome,DF8A Series dome, EH2512 Series enclosure, or EH3512 Series enclosure. The MRD1400H...

Page 5 - MRD ADDRESS SETTINGS; Table B.; MRD DIP Switch Settings; MRD DIP Switch Setting

Pelco Manual C1973M-B (8/03) 5 MRD ADDRESS SETTINGS A camera address setting is required for the controller/switcher to communicate with theMRD1400HZ16. The default setting for the MRD is Receiver Address 1. If you are usingmore than one MRD, each unit must have a different Receiver Address. To chan...

Page 6 - WALL MOUNTING; Wall Mounting; DF5/DF8 SERIES DOME INSTALLATION

6 Pelco Manual C1973M-B (8/03) MRD1400HZ16 INSTALLATION METHODS There are three methods of installation for the MRD1400HZ16. The unit can be mounteddirectly to a wall, or installed inside a dome or enclosure using the supplied mount adapters.Refer to the following sections and select the correct ins...

Page 8 - EH3512 SERIES ENCLOSURE INSTALLATION; Do the following to install the; Control, Power and Camera Connections; section of this manual.; Installing the EH3512 Adapter

8 Pelco Manual C1973M-B (8/03) EH3512 SERIES ENCLOSURE INSTALLATION Do the following to install the MRD1400HZ16 in an EH3512 Series enclosure: 1. Remove the camera sled from the EH3512 Series enclosure. If the camera is attachedto the sled remove the camera. 2. Attach the camera to the 4-inch camera...

Page 9 - EH2512 SERIES ENCLOSURE INSTALLATION; To install the; EH2512 Series Enclosure Installation

Pelco Manual C1973M-B (8/03) 9 EH2512 SERIES ENCLOSURE INSTALLATION To install the MRD1400HZ16 in an EH2512 Series enclosure: 1. Remove the PC board from the MRD1400HZ16. To remove the board: a. Unscrew the two Phillips button head screws from the unit (refer to Figure 2), andremove the cover. Disca...

Page 10 - Make required power connections. Refer to Figure 8.; Table C.; Two-Wire Control Connections; From; Multiple Units with Parallel Connections; Data Cable Wiring

10 Pelco Manual C1973M-B (8/03) CONTROL, POWER, AND CAMERA CONNECTIONS 1. Refer to Figure 8 and Table C. Connect the control wires from the controller to theMRD DATA IN connector. Use the supplied four-pin connector. To connect multipleunits with parallel connections refer to Figure 9. 2. Connect on...

Page 11 - OPERATION; CAMERA OPERATION

Pelco Manual C1973M-B (8/03) 11 OPERATION CAMERA OPERATION PELCO CONTROLLER COMMAND Zoom In Tilt joystick up Zoom Out Tilt joystick down Quickly Zoom In Press the Zoom Tele button or turn the joystick clockwise Quickly Zoom Out Press the Zoom Wide button or turn the joystick counterclockwise Focus N...

Page 12 - REVISION HISTORY; Date; TROUBLESHOOTING; Problem; SPECIFICATIONS; MECHANICAL

12 Pelco Manual C1973M-B (8/03) REVISION HISTORY Manual # Date Comments C1973M 10/01 Original version. C1973M-A 8/02 Revised instructions. C1973M-B 8/03 Revised supplied parts list and installation instructions for DF5/DF8 and EH2512 enclosures. TROUBLESHOOTING Problem Possible Cause and Solutions U...