Pelco MCC5600 - Manuals - manualsarea.com

Page 2 - CONTENTS

2 Pelco Manual C1926M (3/99) LIST OF ILLUSTRATIONS Figure Page 1 Location of Parts and Controls (Front and Rear) ............................................... 4 2 Camera Mounting Screw ................................................................................... 5 3 CA1750 Mount Adapter .......

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; The product may bear the following marks:; DESCRIPTION; Electronic/Passive Iris Control; MODELS; EIA format camera

Pelco Manual C1926M (3/99) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service and installationpersonnel. 2. Installation shall be done in accordance with ...

Page 4 - LOCATION OF PARTS AND CONTROLS; LOCKING RING; FRONT VIEW

4 Pelco Manual C1926M (3/99) LOCATION OF PARTS AND CONTROLS Figure 1. Location of Parts and Controls (Front and Rear) BACK-FOCUS LOCKING RING CS-MOUNT RING 1/3-INCH CCD ELEMENT IRIS CONNECTOR POWER CONNECTOR CAMERA MOUNT (1/4-20 UNC) VIDEO OUTPUT (BNC) V-PHASE ADJUSTMENT 4 2 3 1 PIN 1 = CONTROL COIL...

Page 5 - Figure 2. Camera Mounting Screw; INSTALLATION; CAMERA MOUNTING; Be

Pelco Manual C1926M (3/99) 5 Figure 3. CA1750 Mount Adapter Figure 2. Camera Mounting Screw 7 in. (ASA standard) -inch UNC (20 pitch) INSTALLATION CAMERA MOUNTING Mount the camera using a 1/4–20 mounting screw that does not exceed .197" (4.5 mm ± .2 mm) in length (refer to Figure 2). An optional...

Page 6 - Table A. Video Coaxial Cable Requirements; Maximum Distance; All-copper center conductor; POWER REQUIREMENTS; Model; POWER AND VIDEO CONNECTIONS

6 Pelco Manual C1926M (3/99) Table A. Video Coaxial Cable Requirements Cable Type* Maximum Distance RG59/U 750 ft (229m) RG6/U 1,000 ft (305m) RG11/U 1,500 ft (457m) * Minimum cable requirements: 75 ohms All-copper center conductor All-copper braided shield with 95% braid coverage POWER REQUIREMENTS...

Page 7 - Important Lens Notes:

Pelco Manual C1926M (3/99) 7 LENS INSTALLATION GENERAL LENS INFORMATION MCC5600 Series cameras are factory adjusted to the CS-mount standard. Fixed iris,manual iris, or passive (DC controlled) auto-iris lenses may be used. Passive (DCcontrolled) auto-iris lenses require a standard 4-pin square conne...

Page 8 - LENS MOUNTING; Remove the black protection cover from the CS-mounting ring.; BACK-FOCUS ADJUSTMENT; Fixed Focal Length Lenses

8 Pelco Manual C1926M (3/99) LENS MOUNTING Do not release the back-focus locking ring unnecessarily. Back-focus adjustment has beenset at the factory to the standard CS-mount back-focus distance. To mount a lens: 1. Remove the black protection cover from the CS-mounting ring. 2. If using a C-mount l...

Page 9 - Motorized Zoom Lenses; Using the camera controller, set the lens in the following manner:; CAMERA SYNCHRONIZATION AND V-PHASE; EIA Standard

Pelco Manual C1926M (3/99) 9 b. Adjust the lens and the CS-mount ring together until picture is sharpest. c. Hold the lens and CS-mount ring in place and turn the back-focus locking ringclockwise to tighten. Motorized Zoom Lenses 1. With the camera operating, position the camera to view an object at...

Page 11 - SPECIFICATIONS; Pixels

Pelco Manual C1926M (3/99) 11 SPECIFICATIONS CCD Sensor: 1/3-inch interline transfer Pixels EIA: 768 H x 492 V CCIR: 768 H x 582 V Sensing Area: 3/16 x 1/8 in. (4.7 x 3.5 mm) Sync System: Free running/line lock (when AC powered) HorizontalResolution: ≥ 560 TV lines Iris Control: Electronic/passive L...

Page 12 - REVISION HISTORY; REGULATORY NOTICES; PRODUCT WARRANTY AND RETURN INFORMATION

12 Pelco Manual C1926M (3/99) REVISION HISTORY Manual # Date Comments C1926M 1/98 Original version. 3/99 Added MCC5601-2 model. Revised manual format. Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 1999, Pelco. Endura and ExSite a...