Pelco MC5700 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS AND WARNINGS; DESCRIPTION; MODELS

2 Pelco Manual C1903M (4/99) IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. To prevent fire or shock hazard, do not expose the unit to rain or moisture. C A U T I O N : RISK OF ELECTRIC SHOCK. DO NO...

Page 3 - LOCATION AND FUNCTION OF PARTS; INSTALLATION; LENS; Compatible Lenses

Pelco Manual C1903M (4/99) 3 LOCATION AND FUNCTION OF PARTS Refer to Illustration B for the location of the camera parts listed below. NOTE: References to illus- trations in this manual arekeyed to the illustrations inthe manual that is suppliedwith the camera. B Tripod adapter (may beattached to to...

Page 4 - Changing the Plug on an Auto Iris Lens Cable; PLUG CHANGE ON AUTO IRIS LENS CABLE; Auto Iris Plug

4 Pelco Manual C1903M (4/99) Be sure to attach the lens mount cap when the lens is not mounted. When using an auto-iris lens, use only a DC-driven type or a direct current drive coil with aresistance value over 150 ohms. When using an auto-iris lens, attach it as follows. For a manual lens, omit ste...

Page 5 - Lens Installation

Pelco Manual C1903M (4/99) 5 E A C CS 2 1 4 3 CCD-IRIS ON OFF Lens Installation CCD-Iris Function

Page 6 - CAMERA/LENS GEOMETRY–GENERAL INFORMATION

6 Pelco Manual C1903M (4/99) NOT AVAILABLE ON 5700 SERIES Incident Light LENS CAMERA (STYLIZED) Iris opening (sometimes referred to as aperture) isdefined by f/stop numbers. The higher the numberthe more closed the iris is. IRIS CCDIMAGER CCD Iris (Electronic Shutter) CCD out-put voltage is electron...

Page 8 - BACKFOCUS ADJUSTMENT

8 Pelco Manual C1903M (4/99) Information Box Information Box The purpose of backfocusing is to make the adjustments necessary for the picture to remain in focus throughout the camera’szoom range, which is the case for instance, in motorized zoom, auto iris configurations. Manual Iris lens/camera com...

Page 9 - CAMERA

Pelco Manual C1903M (4/99) 9 CAMERA Install the camera where it will not be affected by fluorescent lights or window reflections.If the camera is used under illumination that is not steady, the picture may flicker. The MC5700-2 must be operated with a 24 VAC, 60 Hz, Class 2 power supply.The MC5700-2...

Page 10 - not

10 Pelco Manual C1903M (4/99) V-PHASE ADJUSTMENT Vertical phase adjustment is required only if your system uses two or more cameras. The vertical phase can be manually adjusted within the range of approximately -90 degreesto +90 degrees (refer to Illustration H). I Vertical Phase H AC Line Lock Adju...

Page 11 - SPECIFICATIONS; Adjusting the Incident Light Level; LEVEL

Pelco Manual C1903M (4/99) 11 INCIDENT LIGHT LEVEL ADJUSTMENT Since the incident light level has been preset at the factory, usually no further adjustment isrequired. If the picture is too dark, however, or if the picture’s highlights are extremelyoverexposed, adjust the LEVEL adjustment screw. This...

Page 12 - REVISION HISTORY; REGULATORY NOTICES

12 Pelco Manual C1903M (4/99) REVISION HISTORY Manual # Date Comments C1903M 11/96 Original version. 4/99 Added MC5700-2X model. Revised manual to new format. ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. Power Consumption MC5700-2: Appr...