Pelco KBD300V - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; Regulatory Notices; CONTENTS; Section

[ 2 ] Pelco Manual C519M-D (7/00) IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. This unit is designed for ...

Page 3 - DESCRIPTION; Models; Function

Pelco Manual C519M-D (7/00) [ 3 ] DESCRIPTION The KBD300V Universal Keyboard can be used in two operational modes. The KBD300V includes a5-inch (12.7 cm) diagonal color monitor to make a complete, stand-alone viewing and control package. CM6700 Mode: Program and operate the CM6700 Matrix Switcher/Co...

Page 5 - Wiring Diagram for Remote Keyboards

Pelco Manual C519M-D (7/00) [ 5 ] Figure 2. Wiring Diagram for Remote Keyboards LOCAL KBD300V INTERFACE SCU R+ R- T- T+ R+ R- T- T+ VIDEO OUTPUTS 1 4 7 5 6 3 2 POWER SUPPLY RX+ RX- GND TX- TX+ TO ADDITIONAL KBD300VINTERFACES OR TO WALLBLOCKS (NON-KBD300VKEYBOARDS) RX+ RX- GND TX- TX+ TO SCU OR PREVI...

Page 6 - INSTALLATION - DIRECT MODE; may not be necessary if another ground path already exists).

[ 6 ] Pelco Manual C519M-D (7/00) 10 Turn on the power switch on the back of the keyboard. The monitor comes on. 11 Go to the Programming and Operation section and program and test for proper operation. INSTALLATION - DIRECT MODE Direct Mode is for a single-keyboard installation only. The keyboard i...

Page 7 - Keyboard Cabling Diagram; C O M M U N I C AT I O N

Pelco Manual C519M-D (7/00) [ 7 ] Figure 3. Keyboard Cabling Diagram V I D E O P O W E R O N O F F I N T E R FA C EC A B L E P O W E R S U P P LY K B D 3 0 0 V V I D E O C O A XC A B L E I N P U T C O M M U N I C AT I O N C A B L E TO R E C E I V E R COM I N COM OU T R+ R– T– T+ R+ R– T– T+

Page 8 - Keyboard Rear Panel; SWITCH SETTINGS; CM6700 accepts only eight addresses.; Keyboard; Keyboard Modes; Direct; Replace the cover plate.

[ 8 ] Pelco Manual C519M-D (7/00) Figure 4. Keyboard Rear Panel SWITCH SETTINGS To set the switches on the keyboard (refer to Figure 4): 1 Remove the two screws and the DIP switch cover plate from the rear of the keyboard. 2 Set the switches: • Address (Switches 1-4) Position the switches according ...

Page 9 - PROGRAMMING AND OPERATION; To view and control cameras on a monitor other than the one on the; Spectra

Pelco Manual C519M-D (7/00) [ 9 ] PROGRAMMING AND OPERATION Table D. Keyboard Functions Circled numbers refer to Figure 5. Function Procedure Select Monitor* LED display 1 shows monitor number in run mode. Enter monitor number (1-4) 15 and press MON 17 to select. NOTE: To view and control cameras on...

Page 13 - Zones; Step

Pelco Manual C519M-D (7/00) [ 13 ] Zones The Zone function is available on Esprit and Spectra positioning systems. This function puts a label onthe screen to identify the viewing area. Zones can also be blanked* to prevent viewing while the camerais positioned in the zone. Up to eight pan (horizonta...

Page 14 - SPECIFICATIONS; GENERAL

[ 14 ] Pelco Manual C519M-D (7/00) SPECIFICATIONS GENERAL Keyboard Keypad: Mechanical Display: Red LED, 7-segment, 2 cells Joystick: 3-axis, vector-solving, with twisting, return-to-center head Shift Mode Indicator: Green LED Storage Temperature: -4 ° to 140 ° F (-20 ° to 60 ° C) Ambient OperatingTe...

Page 15 - INDEX

Pelco Manual C519M-D (7/00) [ 15 ] INDEX A Acknowledge 10Auxiliaries 10 C Clear 10 D DIP switch 8 F Firmware version 10 G Genex multiplexer 3 I Installation CM6700 Mode 4Direct Mode 6 K Keyboard addresses 8 L LED 10Lens Control 9Limit stops 12 M Macro sequence 10Multiplexer displays 10 O Operation 9...

Page 16 - WARRANTY AND RETURN INFORMATION; WARRANTY; RETURNS; REVISION HISTORY; Revised manual to show new DIP switch and switch settings.

[ 16 ] Pelco Manual C519M-D (7/00) ® Pelco, the Pelco logo, Spectra, Genex, Legacy, Coaxitron, and PelcoVision are registered trademarks of Pelco.™ Esprit, Spectra II, and Camclosure are trademarks of Pelco. © Copyright 2000, Pelco. All rights reserved. U.S. Patent No. 411, 530. WARRANTY AND RETURN ...