Pelco IS310-CW - Manuals - manualsarea.com

Page 2 - Important Safety Instructions

2 C3429M-A (1/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such...

Page 3 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

C3429M-A (1/08) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 4 - Description; PARTS LIST; Qty Description

4 C3429M-A (1/08) Description The 310 Series Camclosure ® integrated camera system is a track-light design that mounts to a wall or ceiling. The system incorporates a camera and lens package into a small, unobstructive, medium-security enclosure designed for areas subject to vandalism. The system is...

Page 5 - Installation; PREPARE WALL OR CEILING

C3429M-A (1/08) 5 Installation PREPARE WALL OR CEILING Prepare the wall or ceiling according to one of the following options. • Mounting directly to wall or ceiling Figure 1. Wall/Ceiling Mounting • Mounting to a 4S electrical box with 404 plaster ring Figure 2. Mounting to a 4S Electrical Box • Mou...

Page 6 - CONNECT VIDEO AND POWER; Voltage Red

6 C3429M-A (1/08) • Mounting to a 2-gang electrical box Figure 4. Mounting to a 2-Gang Electrical Box CONNECT VIDEO AND POWER 1. Some indoor installations do not require a heater. If the installation does not require a heater, disconnect the heater wiring. a. Remove the cover with the supplied 1/8-i...

Page 7 - ATTACH BASE

C3429M-A (1/08) 7 Figure 5. Exploded Parts View Figure 6. Camera Mounting Holes ATTACH BASE 1. Release the base locking ring for access to the mounting holes. 2. Attach the base to an adapter plate or conduit adapter using the two 6-32 x 1.25-inch tamper-resistant screws supplied with the adapters. ...

Page 8 - ADJUST ENCLOSURE

8 C3429M-A (1/08) ADJUST ENCLOSURE 1. Turn on power to the camera and monitor. 2. Release one or both locking rings, and swivel the enclosure until the angle of the camera is correct (refer to Figure 7). 3. Tighten the locking rings. Figure 7. Adjusting Enclosure Position 4. If you have a varifocal ...

Page 9 - DN/CH SERIES ADJUSTMENTS; SWITCH SETTINGS

C3429M-A (1/08) 9 DN/CH SERIES ADJUSTMENTS Refer to Figure 9 to adjust the IS310-DN or IS310-CH model. Figure 9. Adjusting the IS310-DN/CH Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Auto Gain Control The automatic gain control (AGC) a...

Page 10 - AUTO IRIS LEVEL ADJUSTMENT; VERTICAL PHASE ADJUSTMENT

10 C3429M-A (1/08) Set to SW4-4 ON to enable flickerless operation. The camera will remove the effects of flickering and the shutter speed will be set to 1/120 (NTSC) or 1/100 (PAL). Set to SW4-4 OFF to disable flickerless operation. This is the default setting. NOTE: If you enable flickerless opera...

Page 11 - Adjusting Vertical Phase; BLEMISH DETECTION

C3429M-A (1/08) 11 Adjusting Vertical Phase You may need two people when synchronizing the cameras: one at the camera, the other at the monitor to observe the vertical roll and the effect of any camera adjustments. To synchronize the cameras: 1. Choose a reference camera to which all other cameras w...

Page 14 - SW1-6: General Maximum Wide Dynamic Range

14 C3429M-A (1/08) SW1-4: Auto White Balance/Manual White Balance Auto white balance (AWB) is enabled by default (ON). To manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video is all white. 3. While holding the background in plac...

Page 18 - Specifications; General

18 C3429M-A (1/08) Specifications General Pan/Tilt Adjustment Manual Pan 180° Tilt 180° Construction Aluminum base and cover, steel camera mounting bracket Finish Gray polyester powder coat Environment Low temperature, indoor/outdoor Operating Temperature -50° to 122°F (-46° to 50°C); de-ices to -10...

Page 19 - PRODUCT WARRANTY AND RETURN INFORMATION; REVISION HISTORY

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...