Pelco IP3701H-2 - Manuals - manualsarea.com

Page 3 - Contents

C2941M-C (6/08) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Open Source Software Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 5 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

C2941M-C (6/08) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 6 - Description; MODELS

6 C2941M-C (6/08) Description The IP3701H-2 Series is a high resolution, color video camera with a built-in 100Base-TX network interface for live streaming to a standard Web browser (Microsoft ® Internet Explorer ® or Firefox ® ). The camera features open architecture connectivity for third-party so...

Page 7 - Basic System Configurations

C2941M-C (6/08) 7 Basic System Configurations IMPORTANT NOTE. PLEASE READ . The network implementations in this document are shown as general representations only and are not intended to show detailed network topologies. Your actual network will differ, requiring changes or perhaps additional networ...

Page 9 - RESET BUTTON

C2941M-C (6/08) 9 Camera Layout Figure 5. Camera Layout RESET BUTTON Use the reset button located on the side of the camera to access the following modes: To access one of these modes: 1. Press and hold the reset button. The unit starts cycling through the modes; hold the button for four seconds to ...

Page 10 - Installation; LENS MOUNTING; CAMERA MOUNTING

10 C2941M-C (6/08) Installation LENS MOUNTING The camera can be used with a fixed iris, manual iris, or auto iris lens. The camera is factory set for a CS mount lens, but is easily adjusted for a C mount lens. 1. C mount lens only: Completely rotate the back focus adjustment counterclockwise before ...

Page 11 - Wiring Tables; CAT5 CABLE

C2941M-C (6/08) 11 Wiring Tables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector. The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply. This sim...

Page 13 - Lens Setup and Focus Procedures; VIDEO DRIVE AUTO IRIS LENS; DIRECT DRIVE DC AUTO IRIS LENS

C2941M-C (6/08) 13 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS 1. Set the lens mode selector switch to AIV. 2. Switch the electronic shutter control (ESC) and automatic gain control (AGC) OFF. 3. Refer to the lens instructions and adjust the lens for the optimum picture (video output ...

Page 14 - MANUAL IRIS LENS; ZOOM LENS

14 C2941M-C (6/08) MANUAL IRIS LENS 1. Set the ESC and AGC switches to ON (default settings). 2. Focus the lens. a. Open the iris fully and set the lens focus to infinity. b. View an image more than 6.5 ft (2 m) away. c. Focus the image with the back focus adjustment ring (refer to Back Focus Adjust...

Page 16 - Switch Settings

16 C2941M-C (6/08) Switch Settings Figure 8. DIP S witch Default S ettings NOTES: • White indicates the switch setting. • Under most conditions, you will not be required to set any switches. ì Backlight compensation (BLC)OFF (default setting) : Disables the BLC mode. BLC: When in the ON position, BL...

Page 18 - Dynamic Range and EDR

18 C2941M-C (6/08) Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges from bright sunlight to deep shadows has a high dynamic range, while indoor scenes with less contrast have a low dynamic range. The extended dynamic r...

Page 19 - Troubleshooting

C2941M-C (6/08) 19 Troubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • Verify Cat5 cable connection.• Verify PoE is enabled.• Disconnect the Cat5 cable from the PoE and then reconnect the cable. Power is indicated by the LED. The LED will flash (green) five times per s...

Page 21 - Specifications

C2941M-C (6/08) 21 Specifications GENERAL ConstructionFinish Black polyester powder coat Imaging Device 1/3-inch imager Picture Elements IP3701H-2 768 (H) x 494 (V) IP3701H-2X 752 (H) x 582 (V) Sensing Area 6 mm diagonally Horizontal Resolution 480 TV lines Iris Control Electronic/passive Minimum Il...

Page 23 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...