Pelco ICS-DO111ABK - Manuals

Page 2 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, hea...

Page 3 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC, ...

Page 4 - Description

Description Designed speciﬁcally for the MR5000 Series public viewing system, the ICS-DO111ABK integrated camera system packages a camera and lens into a small, discreet, high-security dome. Pelco’s MR5000 Series public viewing system is speciﬁ cally designed for retail applications to provide a cle...

Page 5 - Installation; PREPARE VIDEO AND ELECTRICAL CABLING

Installation PREPARE VIDEO AND ELECTRICAL CABLING 1. Temporarily remove the bottom end cap of the MR5000 Series mount if the end cap is installed. 2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount arm and out the bottom end of the mount arm. 3. Pull power w...

Page 8 - Install Camera; 2 VDC operation only:

Install Camera WARNING: Heater elements could be hot! When camera power is on, use caution when adjusting the camera. This applies to all models. 1. Some indoor installations do not require a heater. If the installation does not require a heater, remove the heater board from the camera assembly. To ...

Page 10 - Install Dome and Trim Ring

Install Dome and Trim Ring 1. Align the screw holes in the trim ring with ADJUSTMEN T those in the Camclosure base. GROOV E 2. Domes with Liners (only) – DOME LINER Position the viewing window over the lens of the camera by doing the following: LOOSEN SCREWS a. Loosen the three Phillip screws locate...

Page 11 - AUTO IRIS LEVEL ADJUSTMENT

AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or ﬁxed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. VARIFOCAL LENS FIXED LENS IRIS LEVEL ADJUSTMENT AUTO IRIS LEVEL ADJUSTMENT FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO ...

Page 12 - SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS; Manual backlight compensation:

SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or ﬁ xed lighting conditions where there are no bright spots...

Page 13 - SWITCH SETTINGS FOR VARIFOCAL LENS; AE Functions; Shutter; Switch Number and Position; Speed

SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is conﬁ gured at the factory for automatic exposure. 1 AWB Automatic white balance 2 GAM Gamma function FACTORY SETTINGS 3 AGC Automatic gain control 4 ESC Electronic shutter control 5 BLC Backlight compe...

Page 14 - Specifications; General; Electrical

Speciﬁcations General Operating Temperature -50° to 122°F (-46° to 50°C) De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit ﬁtting and 3/4-inch (1.91 cm) opening for NPT threaded pipe Pan/Tilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel camera mounting bracket ...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series ﬁber optic ...