Pelco DRD14 - Manuals - manualsarea.com

Page 2 - CONTENTS; Section; AMERICAN DYNAMICS

2 Pelco Manual C466M-E (6/99) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 5 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 5 2.0 DESCRIPTION ..................................................

Page 3 - Original Manual

Pelco Manual C466M-E (6/99) 3 LIST OF ILLUSTRATIONS Figure Page 1 PC Board Locations ........................................................................... 8 2 CPU Board ......................................................................................... 9 3 R26/R27 Adjustment Location ......

Page 5 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C466M-E (6/99) 5 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and...

Page 8 - This is not a field installable option.; and; PC Board Locations; CPU BOARD

8 Pelco Manual C466M-E (6/99) 3.0 INSTALLATION Installation of the Dome Receiver/Driver (DRD) into the DD08 or DD14 Dome Driveis accomplished at the factory. This is not a field installable option. 3.1 ADJUSTMENTS Although the DRD has been adjusted and set at the factory, some settings can andmay re...

Page 9 - UNTERMINATED

Pelco Manual C466M-E (6/99) 9 Figure 3. R26/R27 Adjustment Location R26/R27 ADJUSTMENT Figure 2. CPU Board ON 1 2 3 4 5 6 7 8 MADE IN USAPCB8500110D JP2 JP1 RESETSWITCH JP3 JP5 JP6 SW1 UNTERMINATED TERMINATED JP5 and JP6

Page 16 - (AUX 4) with 5 seconds of travel followed by 5 seconds of stop.

16 Pelco Manual C466M-E (6/99) 4.0 OPERATION Upon applying power, the unit starts a configuration routine after 15 seconds. 4.1 SCAN OPERATION Three (3) different scan mode options are offered and can be selected according tooperator preference: Auto Scan; (AUX 2), continuous panning, with a 5-secon...

Page 17 - PRESET FUNCTIONS; Preset commands are

Pelco Manual C466M-E (6/99) 17 4.3 PRESET FUNCTIONS 1. The DRD***2* units are capable of 32 complete preset scenes. On DRD**A2*models, each preset can have a 20-character label. To set a preset, first enterthe label then program the position. 2. Once programmed, the DRD***2* can be commanded to the ...

Page 18 - Receiver/Driver Reset Button Location; Pattern Programming; command. The message; Run Pattern; command. The unit will move; CLEAR VIDEO SCREEN; Clear Video

18 Pelco Manual C466M-E (6/99) Figure 4. Receiver/Driver Reset Button Location 4.6 PATTERNS 1. The DRD***2* units are capable of one 60-second pattern. This pattern canconsist of any standard pan/tilt or lens command. Presets, flip and turbo arenot allowed in a pattern. Zone scan can be enabled whil...

Page 19 - COAXITRON CONTROL COMMAND; PTZ; and tilt and lens) commands the second category is; Extended; Pan speed with values 0 to 0x3F and 0xFF (pan turbo)

Pelco Manual C466M-E (6/99) 19 5.0 FIRMWARE 5.1 COAXITRON CONTROL COMMAND This section describes the protocol used to send commands to the receivers viaCoaxitron. The hardware interface is a 32-bit PWM (pulse width modulated) signal, wherein aone microsecond pulse is considered a zero and a two micr...

Page 21 - Do not use addresses 0 or

Pelco Manual C466M-E (6/99) 21 5.2.2 Addressing The address is set on the CPU board PCB8500110. The switch is labeled SW1.Setting the switch in the “ON” position represents a zero. Refer to Table A. SW1.1 Address Bit 0SW1.2 Address Bit 1SW1.3 Address Bit 2SW1.4 Address Bit 3SW1.5 Address Bit 4SW1.6 ...

Page 24 - The extended commands

24 Pelco Manual C466M-E (6/99) Command Word 3 Word 4 Word 5 Word 6 Set preset XX 00 03 00 01 to 20 Clear preset XX 00 05 00 01 to 20 Go to preset XX 00 07 00 01 to 20 180 Flip preset 00 07 00 21 Zero pan position 00 07 00 22 Set aux XX 00 09 00 01 to 08 Clear aux XX 00 0B 00 01 to 08 Remote Reset 00...

Page 25 - CIRCUIT BOARD PARTS LIST; Circuit Board Parts List; Model

Pelco Manual C466M-E (6/99) 25 6.0 CIRCUIT BOARD PARTS LIST Table C. Circuit Board Parts List Model CPU Board Video Board Power Board Backplane DRD08A11 CPU08A11ASSY PCB8500101ASSY PCB8500130ASSY PCB8500150ASSY DRD08D11 CPU08D11ASSY PCB8500130ASSY PCB8500151ASSY DRD08P11 CPU08P11ASSY PCB8500130ASSY ...

Page 27 - REGULATORY NOTICES

Pelco Manual C466M-E (6/99) 27 7.1 REGULATORY NOTICES NOTE: This equipment has been tested and found to comply with the limits of aClass A digital device, pursuant to part 15 of the FCC rules. These limits aredesigned to provide reasonable protection against harmful interference when theequipment is...

Page 28 - WARRANTY AND RETURN INFORMATION; WARRANTY

28 Pelco Manual C466M-E (6/99) 8.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, wi...