Pelco CM9760 - Manuals - manualsarea.com

Page 2 - Installation Guide

System 9760 ® Installation Guide C1503M (11/99) Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108 International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 3...

Page 3 - CONTENTS; Section; LIST OF ILLUSTRATIONS; Figure

2 Pelco Manual C1503M (11/99) CONTENTS Section Page SYSTEM UNPACKING AND RACKING ............................................................................. 3SYSTEM DATA CONNECTIONS ....................................................................................... 4ADDITIONAL HOOKUP INFORMATI...

Page 4 - SYSTEM UNPACKING AND RACKING; System 9760 Factory Default Port Settings

Pelco Manual C1503M (11/99) 3 This guide is intended to help you with the basic installation and setup of the Pelco System9760 ® Matrix Switcher and Controller. This guide is not a replacement for the system manual, but rather a tool to help you quickly get the system up and running. Before shipping...

Page 5 - Do not apply; SYSTEM DATA CONNECTIONS

4 Pelco Manual C1503M (11/99) 6. Install the system CM9760-CC1 CPU and CM9760-MXB matrix bays near each other.Note that each CM9760-MXB has a unique label for identifying the bay location in theinstallation. This ID information is important in ensuring correct video and data connec-tions. 7. Install...

Page 6 - ADDITIONAL HOOKUP INFORMATION; Comms File; Configuring the System 9760 with the Pelco Window Set 9760 in the; SYSTEM VIDEO CONNECTIONS; DEFINITIONS; A technique to expand the matrix video inputs beyond 256.; VIDEO INPUTS

Pelco Manual C1503M (11/99) 5 ADDITIONAL HOOKUP INFORMATION • Comms File The Comms Setup File contains information about the equipment that is attached toyour system. Access the Comms dialog box by clicking on the Comms tab in the Setup9760 Configuration dialog box. Refer to the Comms Setup File (.S...

Page 7 - SYSTEM PROGRAMMING; After

6 Pelco Manual C1503M (11/99) MULTI-BAY SYSTEMS 1. Down-Framing – For systems with more than 16 monitor outputs, you must pas- sively loop the video from the first CM9760-MXB to the second CM9760-MXB for thenext 16 monitors. The best location for the second bay is below the first bay, as shownin the...

Page 8 - The password is

Pelco Manual C1503M (11/99) 7 DOS The CM9760 system’s program runs in DOS. Therefore, you will need to use basic DOScommands to transfer, overwrite, and edit data, and to maintain files on your hard drive. The default configuration files on the CM9760-CC1 hard drive are defined at the factory andare...

Page 9 - RENAMING CONFIGURATION FILES; Before the files are; SAVE; all

8 Pelco Manual C1503M (11/99) 2. Insert a 3.5-inch floppy disk into the PC. Select the Write File icon on the task bar. This opens the Flat File Utility – Write dialog box. The default for writing flat files is togenerate all files regardless of whether or not they are used. To write only specific f...

Page 10 - SYSTEM PORT SETTINGS TABLE

Pelco Manual C1503M (11/99) 9 5. Change the command line in the autoexec.bat file to reflect the new flat files name:from TEST to newfilename (the name you chose in step 2 above). 6. Click File , then Save . 7. You also need to change the test.bat file to reflect the new flat files name, otherwiseth...

Page 11 - The number of ports on your system may differ from the; P O R T

10 Pelco Manual C1503M (11/99) PRINTER COM1 COM2 5 6 7 8 9 10 11 12 20 19 18 17 16 15 14 13 28 27 26 25 24 23 22 21 36 35 34 33 32 31 30 29 System 9760 Factory Default Port Settings Note: The number of ports on your system may differ from the above drawing. Connect System 9760 components as follows:...

Page 12 - SETUP DRAWINGS; CM9760-MXB Typical Connections; TYPICAL CONNECTIONS

Pelco Manual C1503M (11/99) 11 SETUP DRAWINGS P R I N T E R C O M 1 C O M 2 3 5 2 9 2 8 2 1 2 0 1 3 1 2 5 LPT PRINTER PORT FAN POWER INPUT POWER SWITCH AT KEYBOARD PORT VGA PORT OPTIONAL RELAY PORT RS-232 PORT 1 RS-232 PORT 2 PORT 36 PORT 29 PORT 28 PORT 21 PORT 20 PORT 13 PORT 12 PORT 5 RS-422 PORT...

Page 13 - CAMS

12 Pelco Manual C1503M (11/99) P R I N T E R C O M 1 C O M 2 3 5 2 9 2 8 2 1 2 0 1 3 1 2 5 Alarm Black Out RS-422 RS-422 Alarm Black Out RS-422 RS-422 CAMS 257-496 CAMS 1-256 481 257 241 1 REFER TO PORTASSIGNMENT PAGEFOR YOUR SYSTEM’SSPECIFIC DATACONNECTIONS CM9760-CC1 CM9760-MXB CM9760-MXB 16 1 Fig...

Page 40 - NOTES

Page 41 - WARRANTY AND RETURN INFORMATION; REVISION HISTORY

40 Pelco Manual C1503M (11/99) ® Pelco, the Pelco logo, and System 9760 are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defec-tive in material or workmanship for a period of one year after...