Pelco CC3710UH SERIES - Manuals

Pelco CC3710UH SERIES – Manual in PDF format online.

Manuals:

Manual

Manual Pelco CC3710UH SERIES

Summary

Page 4 - IMPORTANT SAFETY INSTRUCTIONS

[ 4 ] Pelco Manual C2933M (10/05) This symbol indicates that dangerous voltageconstituting a risk of electric shock is presentwithin this unit. This symbol indicates that there are impor-tant operating and maintenance instructionsin the literature accompanying this unit. Please thoroughly familiariz...

Page 5 - REGULATORY NOTICES; Reorient or relocate the receiving antenna.

Pelco Manual C2933M (10/05) [ 5 ] REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may ...

Page 6 - DESCRIPTION; Models

[ 6 ] Pelco Manual C2933M (10/05) DESCRIPTION CC3610UH and CC3710UH Series cameras are color video cameras with a 1/3-inch CCD imager. All cameras havea direct drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses. Models CC3610UH-6 Ultra-high resolution (540 TV l...

Page 7 - CAMERA LAYOUT; Figure 1. Camera Layout; INSTALLATION; Lens Mounting; Auto Iris Lens Only -; PIN; Not used

Pelco Manual C2933M (10/05) [ 7 ] CAMERA LAYOUT Figure 1. Camera Layout INSTALLATION Lens Mounting CC3610UH and CC3710UH Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses.Cameras are factory-set for CS-mount lenses, but are easily adjusted for C-mount lenses. 1. C-Mou...

Page 8 - Camera Mounting; times the combined weight of the camera and lens.; Figure 3. Camera Mounting

[ 8 ] Pelco Manual C2933M (10/05) Camera Mounting Mounting points are provided on the top and bottom of the camera and are used to mount the camera on abracket or tripod. They are designed to accept standard photographic mounting bolts (1/4-inch UNC-20). Themounting bracket must be capable of suppor...

Page 9 - CONNECTIONS; Video Connections; BNC connector to the BNC; Table A. Video Coaxial Cable Requirements; Power Connections; Mains Power Supply

Pelco Manual C2933M (10/05) [ 9 ] CONNECTIONS CC3610UH and CC3710UH Series cameras offer standard power and coax video connectors as well as anRJ45-10 connector that combines low voltage power and video (composite or UTP). These cameras also havea service connector allowing a video monitor to be con...

Page 10 - Low Voltage Power Supply; a minimum wire gauge of 24 AWG.

[ 10 ] Pelco Manual C2933M (10/05) Low Voltage Power Supply Cameras fitted with an automatic-switching low voltage power supply operate at 10.8 to 13.8 VDC (12 VDC-10% +15%) or 20.4 to 27.6 VAC (24 VAC ±15%) at 50/60Hz. Connections and polarity are indicated adjacent tothe screw terminals on the rea...

Page 12 - Ser vice Connection; Figure 5. Service Connector; the rear panel of the camera.; 4 VAC/12 VDC Power Connection

[ 12 ] Pelco Manual C2933M (10/05) Ser vice Connection The service connector allows a video monitor to be connected locally to the camera using a 2.5 mm plug tocomposite video BNC cable. Figure 5. Service Connector NOTE: Inserting the plug into the service connector disconnects video from the compos...

Page 13 - CAMERA SETUP; Lens Setup and Focus Procedures; Video Drive or Direct Drive (DC) Auto Iris Lens; Remove the ND filter and set the lens focus as required.; Fixed Lens; sensitivity, the smallest aperture the greatest depth of field.; Zoom Lens; For best results outdoors use an ND3 (neutral density) filter.

Pelco Manual C2933M (10/05) [ 13 ] CAMERA SETUP Lens Setup and Focus Procedures Video Drive or Direct Drive (DC) Auto Iris Lens 1. Set the ESC switch and AGC switch to OFF.2. Adjust the lens for the optimum picture. Video Drive Refer to the lens instructions and adjust the lens for the optimum pictu...

Page 14 - Back Focus Adjustment; To adjust the back focus:; Figure 7. Back Focus Adjustment

[ 14 ] Pelco Manual C2933M (10/05) Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. Turn the back focus ring counterclockw...

Page 15 - Switch Settings; before making any adjustments.; - Enables the Electronic Shutter Control mode.; Switch Setting 3; Figure 8. Switch Settings

Pelco Manual C2933M (10/05) [ 15 ] Switch Settings NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. AGC (Automatic Gain Control) - Switch Setting 1 Automatically adjusts the image to compensate for low levels ...

Page 17 - Camera Synchronization; To line lock the cameras, do the following:

Pelco Manual C2933M (10/05) [ 17 ] Camera Synchronization When using more than one camera power supply, a brief vertical roll may occur on the monitor when a cameraview is switched. To eliminate this vertical roll, it is necessary for the cameras to be synchronized. If the camerasare connected to ce...

Page 18 - SPECIFICATIONS; GENERAL

[ 18 ] Pelco Manual C2933M (10/05) SPECIFICATIONS GENERAL Imaging Device: 1/3-inch interline transfer CCD Picture Elements CC3610UH and CC3710UH: NTSC 768 (H) x 494 (V); PAL 752 (H) x 582 (V) Sensing Area: 6 mm diagonal Scanning System NTSC: 525 lines, 2:1 interlace PAL: 625 lines, 2:1 interlace Syn...

Page 23 - Date

Pelco Manual C2933M (10/05) [ 23 ] REVISION HISTORY Manual # Date Comments C2933M 10/05 Original version.