Pelco CC3710 - Manuals

Pelco CC3710 – Manual in PDF format online.

Manuals:

Manual

Manual Pelco CC3710

Summary

Page 4 - IMPORTANT SAFETY INSTRUCTIONS

[ 4 ] Pelco Manual C2914M-F (08/05) This symbol indicates that dangerous voltageconstituting a risk of electric shock is presentwithin this unit. This symbol indicates that there are impor-tant operating and maintenance instructionsin the literature accompanying this unit. Please thoroughly familiar...

Page 5 - REGULATORY NOTICES; Reorient or relocate the receiving antenna.

Pelco Manual C2914M-F (08/05) [ 5 ] REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that ma...

Page 6 - DESCRIPTION; Models

[ 6 ] Pelco Manual C2914M-F (08/05) DESCRIPTION CC3610 and CC3710 Series cameras are color video cameras with a 1/3-inch CCD imager. All cameras have adirect drive/auto iris lens connector and adjustable back focus, and they accept C and CS lenses. Models CC3610H-6 High resolution (480 TV lines), Ex...

Page 7 - CAMERA LAYOUT; Figure 1. Camera Layout; INSTALLATION; Lens Mounting; Auto Iris Lens Only -; PIN; Not used

Pelco Manual C2914M-F (08/05) [ 7 ] CAMERA LAYOUT Figure 1. Camera Layout INSTALLATION Lens Mounting CC3610 and CC3710 Series cameras can use fixed iris, manual iris, auto iris, or direct drive lenses. Camerasare factory-set for CS-mount lenses, but are easily adjusted for C-mount lenses. 1. C-Mount...

Page 8 - Camera Mounting; times the combined weight of the camera and lens.; Figure 3. Camera Mounting

[ 8 ] Pelco Manual C2914M-F (08/05) Camera Mounting Mounting points are provided on the top and bottom of the camera and are used to mount the camera on abracket or tripod. They are designed to accept standard photographic mounting bolts (1/4-inch UNC-20). Themounting bracket must be capable of supp...

Page 9 - CONNECTIONS; Video Connections; BNC connector to the BNC; Table A. Video Coaxial Cable Requirements; Power Connections; Mains Power Supply

Pelco Manual C2914M-F (08/05) [ 9 ] CONNECTIONS CC3610 and CC3710 Series cameras offer standard power and coax video connectors as well as an RJ45-10connector that combines low voltage power and video (composite or UTP). These cameras also have a serviceconnector allowing a video monitor to be conne...

Page 10 - Low Voltage Power Supply; a minimum wire gauge of 24 AWG.

[ 10 ] Pelco Manual C2914M-F (08/05) Low Voltage Power Supply Cameras fitted with an automatic-switching low voltage power supply operate at 10.8 to 13.8 VDC (12 VDC-10% +15%) or 20.4 to 27.6 VAC (24 VAC ±15%) at 50/60Hz. Connections and polarity are indicated adjacent tothe screw terminals on the r...

Page 12 - Ser vice Connection; Figure 5. Service Connector; the rear panel of the camera.; 4 VAC/12 VDC Power Connection

[ 12 ] Pelco Manual C2914M-F (08/05) Ser vice Connection The service connector allows a video monitor to be connected locally to the camera using a 2.5 mm plug tocomposite video BNC cable. Figure 5. Service Connector NOTE: Inserting the plug into the service connector disconnects video from the comp...

Page 13 - CAMERA SETUP; Lens Setup and Focus Procedures; Video Drive or Direct Drive (DC) Auto Iris Lens; Remove the ND filter and set the lens focus as required.; Fixed Lens; sensitivity, the smallest aperture the greatest depth of field.; Zoom Lens; For best results outdoors use an ND3 (neutral density) filter.

Pelco Manual C2914M-F (08/05) [ 13 ] CAMERA SETUP Lens Setup and Focus Procedures Video Drive or Direct Drive (DC) Auto Iris Lens 1. Set the ESC switch and AGC switch to OFF.2. Adjust the lens for the optimum picture. Video Drive Refer to the lens instructions and adjust the lens for the optimum pic...

Page 14 - Back Focus Adjustment; To adjust the back focus:; Figure 7. Back Focus Adjustment

[ 14 ] Pelco Manual C2914M-F (08/05) Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. To adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. Turn the back focus ring countercloc...

Page 15 - Switch Settings; before making any adjustments.; - Enables the Electronic Shutter Control mode.; Switch Setting 3; Figure 8. Switch Settings

Pelco Manual C2914M-F (08/05) [ 15 ] Switch Settings NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments. AGC (Automatic Gain Control) - Switch Setting 1 Automatically adjusts the image to compensate for low level...

Page 17 - Camera Synchronization; To line lock the cameras, do the following:

Pelco Manual C2914M-F (08/05) [ 17 ] Camera Synchronization When using more than one camera power supply, a brief vertical roll may occur on the monitor when a cameraview is switched. To eliminate this vertical roll, it is necessary for the cameras to be synchronized. If the camerasare connected to ...

Page 18 - SPECIFICATIONS; GENERAL

[ 18 ] Pelco Manual C2914M-F (08/05) SPECIFICATIONS GENERAL Imaging Device: 1/3-inch interline transfer CCD Picture Elements CC3710H and CC3610H: NTSC 768 (H) x 494 (V); PAL 752 (H) x 582 (V) CC3710S: NTSC 510 (H) x 492 (V); PAL 500 (H) x 582 (V) Sensing Area: 6 mm diagonal Scanning System NTSC: 525...

Page 23 - Date

Pelco Manual C2914M-F (08/05) [ 23 ] REVISION HISTORY Manual # Date Comments C2914M 05/04 Original version. C2914M-A 07/04 Lens connector pin out changed. C2914M-B 09/04 Clarified instructions for UTP use. C2914M-C 11/04 Added UL warning for high-voltage models. C2914M-D 11/04 Revised safety instruc...