Pelco CC3701H-2X - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS AND WARNINGS; RISK OF ELECTRIC SHOCK.

[ 2 ] Pelco Manual C1937M-C (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth...

Page 3 - REGULATORY NOTICES; Reorient or relocate the receiving antenna.; Models

Pelco Manual C1937M-C (4/03) [ 3 ] REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class B digital device, pursuantto part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installat...

Page 4 - Lens Mounting; Back Focus Adjustment; PIN

[ 4 ] Pelco Manual C1937M-C (4/03) CAMERA LAYOUT Figure 1. Camera Layout INSTALLATION Lens Mounting The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mountlens, but is easily adjusted for a C-mount lens. 1. C-Mount Lens Only - Rotate the back focus ad...

Page 7 - LENS SETUP AND FOCUS PROCEDURES; Video Drive Auto Iris Lens; BACK FOCUS ADJUSTMENT; To adjust the back focus:

Pelco Manual C1937M-C (4/03) [ 7 ] LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens Set the lens mode selector switch to AIV. Switch the ESC and AGC OFF. Refer to the lens instructions andadjust the lens for the optimum picture (video output level of 1V peak-to-peak). To focus, fully open ...

Page 8 - SWITCH SETTINGS; BLC

[ 8 ] Pelco Manual C1937M-C (4/03) SWITCH SETTINGS Figure 6. DIP Switch Default Settings OFF OFF OFF OFF AIV INT NOR OFF OFFAW1 BLC AGC OPT ESC AID LL SHP LC EDR AW2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 20157 1 BLC - Back Light Compensation OFF (Default setting) - Disables the BLC mode. BLC -...

Page 10 - CAMERA SYNCHRONIZATION (AC OPERATION ONLY); To synchronize the cameras do the following:

[ 10 ] Pelco Manual C1937M-C (4/03) CAMERA SYNCHRONIZATION (AC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitor when acamera view is switched. To eliminate vertical roll, adjust the phase control by synchronizing, or line-lock-ing, the came...

Page 11 - SPECIFICATIONS; GENERAL

Pelco Manual C1937M-C (4/03) [ 11 ] SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements CC3701H-2: 768 (H) x 494 (V) CC3701H-2X: 752 (H) x 582 (V) Sensing Area: 6 mm diagonally Synchronize System: INT/AC line lock Horizontal Resolution CC3701H-2: 480 TV lines CC3701H-2X: ...

Page 12 - REVISION HISTORY; Date; Revised the lens connector wiring chart.; WARRANTY AND RETURN INFORMATION

[ 12 ] Pelco Manual C1937M-C (4/03) REVISION HISTORY Manual # Date Comments C1937M 3/02 Original version. C1937M-A 5/02 Revised the lens connector wiring chart. C1937M-B 8/02 Added certifications. Revised Important Safeguards and Warnings. C1937M-C 4/03 Added S-mark certification. ® Pelco, the Pelco...