Pelco CC3551H-2 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS AND WARNINGS; The product and/or manual may bear the following marks:

[ 2 ] Pelco Manual C1984M-F (4/03) Prior to installation and use of this product, the following WARNINGS should be observed. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth...

Page 3 - REGULATORY NOTICES; Reorient or relocate the receiving antenna.; DESCRIPTION; Models

Pelco Manual C1984M-F (4/03) [ 3 ] REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class A digital device, pursuantto part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installat...

Page 4 - Lens Mounting; Back Focus Adjustment; PIN

[ 4 ] Pelco Manual C1984M-F (4/03) CAMERA LAYOUT Figure 1. Camera Layout INSTALLATION Lens Mounting The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mountlens, but is easily adjusted for a C-mount lens. 1. C-Mount Lens Only - Rotate the back focus ad...

Page 7 - LENS SETUP AND FOCUS PROCEDURES; Video Drive Auto Iris Lens; Manual Iris Lens; Zoom Lens; BACK FOCUS ADJUSTMENT; To adjust the back focus:

Pelco Manual C1984M-F (4/03) [ 7 ] LENS SETUP AND FOCUS PROCEDURES Video Drive Auto Iris Lens Set the lens mode selector switch to AIV. Switch the ESC OFF. Refer to the lens instructions and adjust thelens for the optimum picture (video output level of 1V peak-to-peak). To focus, fully open the iris...

Page 8 - SWITCH SETTINGS; BLC

[ 8 ] Pelco Manual C1984M-F (4/03) SWITCH SETTINGS Figure 6. DIP Switch Default Settings OFFOFFOFF AW1 AIV INT NOR OFF OFFOFF BLC OPTESC AW2 AIDLLSHPLCDS1 DS2 ON PHASE LEVEL + - H L 1 2 3 4 5 6 7 8 9 10 00027 Note: White indicates switch setting. 1 BLC - Back Light Compensation OFF (Default setting)...

Page 9 - White represents switch postion.; LC; Long Line Compensation; DS1 and; - Digital Slow Shutter

Pelco Manual C1984M-F (4/03) [ 9 ] OFF - Disables the DSS mode. 4 Fields of Integration Maximum - 1/15-second scene update rate. 16 Fields of Integration Maximum - 1/4-second scene update rate. 30 Fields of Integration Maximum (Default setting) - 1/2-second scene update rate. NOTE: White represents ...

Page 10 - CAMERA SYNCHRONIZATION (AC OPERATION ONLY); To synchronize the cameras do the following:

[ 10 ] Pelco Manual C1984M-F (4/03) CAMERA SYNCHRONIZATION (AC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitor when acamera view is switched. To eliminate vertical roll, adjust the phase control by synchronizing, or line-lock-ing, the came...

Page 11 - SPECIFICATIONS; GENERAL

Pelco Manual C1984M-F (4/03) [ 11 ] the vertical sync pulses of the reference camera to the selected camera(s). SPECIFICATIONS GENERAL CCD Sensor: 1/3-inch interline transfer Picture Elements CC3551H-2: 768 (H) x 494 (V) CC3651H-2X: 795 (H) x 696 (V) Sensing Area: 6 mm diagonally Synchronize System:...

Page 12 - WARRANTY AND RETURN INFORMATION

[ 12 ] Pelco Manual C1984M-F (4/03) REVISION HISTORY Manual # Date Comments C1984M 10/00 Original version. C1984M-A 12/00 Added note for cosmetic trim ring. Revised switch setting illustration to depict default settings. C1984M-B 7/01 Added camera model CC3651H-2X. C1984M-C 11/01 Modified direct dri...