Pelco C554M (2/98) - Manuals

Page 2 - CONTENTS; LIST OF ILLUSTRATIONS

2 Pelco Manual C544M (2/98) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 3 2.0 DESCRIPTION ....................................................

Page 3 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C544M (2/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and s...

Page 5 - GENERAL FEATURES; A fully populated Pelco 9760-IRC unit consists of the following:; VCR Hook-up Parameters; UP TO TOTAL OF

Pelco Manual C544M (2/98) 5 2.1 GENERAL FEATURES The Pelco 9760-IRC is housed in a rack frame and connects to one Sercom port onthe rear of the CM9760-CC1. • A fully populated Pelco 9760-IRC unit consists of the following: a. One communication card (interfaces with CM9760-CC1) b. Four VCR control ca...

Page 6 - Sample System Hook-up

6 Pelco Manual C544M (2/98) 2.2 SAMPLE SYSTEM A typical system installation involving the CM9760-IRC might include: a. CM9760-CC1 e. Monitors b. CM9760-IRC f. Cameras c. CM9760-KBD g. CM9760-MXBs d. VCRs Other Pelco products can be added according to system requirements. Figure 3. Sample System Hook...

Page 7 - ON; Communication Card

Pelco Manual C544M (2/98) 7 3.0 INSTALLATION To install the Pelco Infrared VCR Controller, proceed as follows: 1. Set the baud. 2. Set the start address. 3. Connect the CM9760-IRC to the CM9760-CC1 host. 4. Connect additional IRC units in daisy-chain fashion. 5. Connect VCRs to the Video Matrix Bay ...

Page 8 - The operating baud must; Baud Settings; The VCRs connected to a

8 Pelco Manual C544M (2/98) 3.1.1 Setting the Baud Bauds of 2400, 4800, 9600, and 19200 are available. The communication protocoluses eight data bits, one stop bit, and even parity. The baud is set using DIP switches 1 and 2 according to Table A. NOTE: The operating baud must match the baud rate set...

Page 9 - It is necessary only to set the

Pelco Manual C544M (2/98) 9 3.2.1 Setting the Start Address Each Pelco CM9760-IRC unit requires a six-bit start address. The start address isconfigured using the DIP switches on the communication card (see Figure 5: DIPswitches). Each control card occupies one address space. An IRC unit occupiesfour...

Page 11 - via Serial GPI; Connecting IRCs in Sequence; CONNECTING ADDITIONAL IRCs IN SEQUENCE; The data pin connections are shown below in Figure 9.; Sixteen is the maximum; Data Pin Connections for IRC’s in Sequence; IN

Pelco Manual C544M (2/98) 11 3.3.1 Connecting the CM9760-IRC to a CM9760-CC1 Host via Serial GPI A CM9760-IRC can be daisy-chained from a serial GPI already connected to aSerCom port of a CM9760-CC1 (CPU). The wiring is the same as for Section 3.3. Connect the RS-422 OUT port of the serial GPI to th...

Page 12 - CONNECTING VCRs TO THE VIDEO MATRIX BAY; VIDEO MATRIX BAY

12 Pelco Manual C544M (2/98) 3.5 CONNECTING VCRs TO THE VIDEO MATRIX BAY (CM9760-MXB) VCRs must be connected to the CM9760-MXB (Video Matrix Bay). Two standardcoaxial cables are needed: (1) One to run from the VIDEO OUT port on the back of the VCR to the desired INport on the VMB. (2) The other to r...

Page 13 - VCR CONTROL SIGNAL OUTPUTS; The wiring for each DB9 output is shown below in Table D.; IR Control Cable Wiring; Pin; Once installation has been

Pelco Manual C544M (2/98) 13 3.6 VCR CONTROL SIGNAL OUTPUTS An IRC has up to 32 D9 female output connections numbered J1 to J32, each ableto control four VCRs (refer to Figure 6). Every DB9 output supports four IR controlcables. Each IR control cable controls the functions of a single VCR. The wirin...

Page 14 - Electrical Specifications; 5 vA per control card and communication card; Communications; Even; Mechanical

14 Pelco Manual C544M (2/98) 4.0 SPECIFICATIONS Electrical Specifications OperatingVoltages: 120 or 230 VAC 50/60 Hz. ± 10%, selectable PowerConsumption: 15 vA per control card and communication card OperatingTemperatureRange: 32 ° to 122 ° F (0 ° to 50 ° C) Communications SerialCommunicationPorts: ...

Page 15 - NOTES

Page 16 - WARRANTY AND RETURN INFORMATION; WARRANTY

16 Pelco Manual C544M (2/98) 5.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1998, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, with...