Pelco C454M-C - Manuals - manualsarea.com

Page 2 - CONTENTS; Section

2 Pelco Manual C454M-C (1/98) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 5 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 51.2 UNPACKING INSTRUCTIONS ........................................

Page 5 - The product and/or manual may bear the following marks:

Pelco Manual C454M-C (1/98) 5 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and...

Page 6 - UNPACKING INSTRUCTIONS; Suspended Ceiling Models; RECOMMENDED TOOLS

6 Pelco Manual C454M-C (1/98) 1.2 UNPACKING INSTRUCTIONS Unpack and inspect all parts carefully. Be sure to save the shipping carton and any inserts. They are the safest material inwhich to make future shipments. If an item appears to have been damaged in shipment, replace it properly in itscarton a...

Page 9 - If you are going to install a

Pelco Manual C454M-C (1/98) 9 3.0 INSTALLATION 3.1 MOUNTING The Intercept ® Series of domes provide back box configurations for several applica- tions and environments (refer to Figures 12 and 13). Installation instructions for the applications listed below will appear in the followingorder: 1. Susp...

Page 11 - The length of pipe used may; For outdoor models apply

Pelco Manual C454M-C (1/98) 11 3.1.3 Pendant Mounting The pendant back box is designed to be suspended from a suitable length of 1-1/2”pipe threaded at both ends. This pipe can be interfaced to the IWM Series or IDM4018wall mounts or to the MRWA wall adapter mount or MRCA ceiling adapter mount. To i...

Page 12 - WIRING INSTRUCTIONS

12 Pelco Manual C454M-C (1/98) 3.2 WIRING INSTRUCTIONS How your back box will be wired depends on the type of unit you have: Units with an on-board receiver/driverUnits without an on-board receiver/driver (hard-wire applications) Hardwire refers to installations using a remote receiver/driver or a t...

Page 13 - Table A. Video Coaxial Cable Requirements; Wire Gauge; Maximum distance from transformer to load; An enclosure that re-; Distances are calculated in

Pelco Manual C454M-C (1/98) 13 Table A. Video Coaxial Cable Requirements Cable Type* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) * Minimum cable requirements: 75 ohmsAll-copper center conductorAll-copper braided shield with 95% braid coverage Wire Gauge Maxi...

Page 17 - Preset SL Models

Pelco Manual C454M-C (1/98) 17 3.2.2 Hard-Wire or Remote Receiver/Driver Refer to Figures 6 and 7 for wiring diagrams. Refer to Table A for the type of video coaxial cable to use. On models for suspended ceilings or hard ceilings, a plate is provided on the top ofthe back box with 1/2" and 3/4&#...

Page 20 - DOME DRIVE INSTALLATION

20 Pelco Manual C454M-C (1/98) 3.2.3 Heater/Blower Kit Field Installation The kits are shipped partially assembled, to complete assembly and to install theheater/blower kit perform the following steps: 1. Place the fan over the four (4) unused internally threaded standoffs located onthe back plate (...

Page 21 - EXPLODED ASSEMBLY DIAGRAMS; Figure 8. Suspended Ceiling Back Box Exploded Assembly Diagram

Pelco Manual C454M-C (1/98) 21 4.0 EXPLODED ASSEMBLY DIAGRAMS Figure 8. Suspended Ceiling Back Box Exploded Assembly Diagram Table C. Suspended Ceiling Back Box Exploded Assembly Parts List Item Quantity Description Part Number 1 1 Trim ring, white SB262ASSY 2 1 Back box 8144287COMP 3 1 Faceplate, d...

Page 24 - Figure 11. Back Plate Exploded Assembly Diagram

24 Pelco Manual C454M-C (1/98) Figure 11. Back Plate Exploded Assembly Diagram

Page 25 - Table F. Back Plate Exploded Assembly Parts List (Figure 11)

Pelco Manual C454M-C (1/98) 25 Table F. Back Plate Exploded Assembly Parts List (Figure 11) Item Quantity Description Part Number 1 2 Latch backup plate 8004244COMP 2 2 Latch 8004105COMP 3 2 Latch bracket 8004143COMP 4 1 Transformer (120 VAC model only) TRF21243.30.70F 5 1 25-position connector plug...

Page 26 - It is not recommended using

26 Pelco Manual C454M-C (1/98) 5.0 SPECIFICATIONS ELECTRICAL Enclosure Back Box Input Voltage: 24 VAC or 120 VAC Power Requirements Receiver/Driver: 48 vA for 24 VAC and 120 VAC dome drives Blowercontinuous duty: One (1) at 30 cfm, 1.92 watts, 24 VDC One (1) at 33 cfm, 6.7 watts, 120 VAC 60 Hz One (...

Page 28 - WARRANTY AND RETURN INFORMATION; WARRANTY

28 Pelco Manual C454M-C (1/98) 6.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one (1) year after the date of shipment.Exceptions to this warranty are as noted below: • Two (2) years...