Pelco C342M-PSA (11/98) - Manuals

Page 2 - CONTENTS; Section

2 Pelco Manual C342M-PSA (11/98) 2 CONTENTS Section Page 1.0 GENERAL ................................................................................................... 5 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 5 2.0 DESCRIPTION ............................................

Page 5 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C342M-PSA (11/98) 5 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation ...

Page 7 - To insure proper wiring and

Pelco Manual C342M-PSA (11/98) 7 3.0 INSTALLATION 3.1 MOUNTING Attach the pan/tilt unit to a wall or ceiling mount. Follow the instructions that areprovided with the mount. Make sure the mounting surface and the selected mountcan support four times the combined weight of the pan/tilt unit and the ca...

Page 8 - To prevent

8 Pelco Manual C342M-PSA (11/98) 3.3.2 All Control Equipment Except LRD41A11-X Legacy Receiver/Drivers Make the interconnecting cable to link the 37-pin round connector from the pan/tiltunit to the control equipment. For cable requirements, refer to the following tables: Table A: Connector Pin Desig...

Page 9 - Figure 1. Connector Assembly

Pelco Manual C342M-PSA (11/98) 9 1 CABLE HOUSING A SHELL B CLAMP 2 RUBBER BOOT 3 CABLE 4 SOCKET 5 CABLE PLUG (37-POSITION) Figure 2. Wiper On/Off Connection Figure 1. Connector Assembly

Page 10 - Table A. 37-Position Connector Pin Designations; Function

10 Pelco Manual C342M-PSA (11/98) Table A. 37-Position Connector Pin Designations Pin # Function ENGPT780-24P/PP ENGPT780-24SL/P Coaxial Cable 27/4 Video Signal/Ground • • 30/4 Sync Signal/Ground • • Unshielded Conductors 3 Left • • 7 Right • • 6 Up • • 5 Down • • 1 Common • • 8 Safety Ground • • 10...

Page 11 - Operation of the pan/tilt unit

Pelco Manual C342M-PSA (11/98) 11 Table B. Requirements to Wire Power to Pan and Tilt Motors Maximum Cable Length* Wire Size 6 Conductors** 7 Conductors*** 24 VAC PT780-24P Models 20 AWG 59 ft. (17.98 m) 118 ft. (35.96 m) 18 AWG 94 ft. (28.65 m) 188 ft. (57.30 m) 16 AWG 149 ft. (45.41 m) 298 ft. (90...

Page 12 - PAN AND TILT LIMIT STOP ADJUSTMENTS; Figure 3. Removing the Screws

12 Pelco Manual C342M-PSA (11/98) 3.4 PAN AND TILT LIMIT STOP ADJUSTMENTS 1. Remove the covers. a. Refer to Figure 3 and remove the Phillips screw on each side of the pan/tilt unit. b. Refer to Figure 4 and place your hands under the cover halves. Exert astrong, upward force to release the covers fr...

Page 13 - Figure 7. Tilt Limit Adjustment; Adjust the tilt limit stops.

Pelco Manual C342M-PSA (11/98) 13 Figure 7. Tilt Limit Adjustment 3 4 2 1 10 G H 9 A B C D 8 7 E F 6 5 2. Adjust the tilt limit stops. Refer to Figure 7 for the location of the tilt limit stops (item 7). Turn the controlunit on and tilt the unit to the desired up position. Move the up limit cam unti...

Page 14 - The SL model does not have; Figure 8. Pan Limit Adjustment

14 Pelco Manual C342M-PSA (11/98) 3. Adjust the pan limit stops. Refer to Figure 8 for the location of the pan limit stops. Turn the control unit onand pan the unit to the desired right limit stop. Move the right limit stop until it touches the limit switch actuator. Push the stopagainst the actuato...

Page 15 - FINAL INSTALLATION; Replace the screws in the covers.; Figure 10. Replacing the Cover Halves

Pelco Manual C342M-PSA (11/98) 15 3.5 FINAL INSTALLATION 1. If the pan/tilt is installed in an inverted position, refer to Figure 9 and applyRTV silicone (such as Bostik #9732 or equivalent) to the shaded areas of thecovers. 2. Replace the covers. a. Refer to Figure 10 and grasp one cover half in ea...

Page 19 - EXPLODED ASSEMBLY DIAGRAMS; Figure 14. Exploded Assembly Diagram of Mechanical Parts

Pelco Manual C342M-PSA (11/98) 19 6.0 EXPLODED ASSEMBLY DIAGRAMS Figure 14. Exploded Assembly Diagram of Mechanical Parts

Page 23 - Figure 16. Exploded Assembly Diagram of Hardware

Pelco Manual C342M-PSA (11/98) 23 Figure 16. Exploded Assembly Diagram of Hardware EE W J BB J W J CC Q E F E F A B C D M T S PP G H I J K L EE FF I J I J MM LL X GG Z T S Y W J R S T J W BB A* B* C* D* HH II JJ KK ** ** ** ** E F NN N D Q N M I J DD E F P V U AA

Page 28 - WARRANTY AND RETURN INFORMATION; WARRANTY

28 Pelco Manual C342M-PSA (11/98) 9.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Excep-tions to this warranty are as noted below: • Three years ...