Page 3 - Contents
C3426M-A (5/07) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4 - List of Illustrations
4 C3426M-A (5/07) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 Basic Surface Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3...
Page 5 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE
C3426M-A (5/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...
Page 6 - Description; MODELS; Camera Type
6 C3426M-A (5/07) Description The IS110 Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications an...
Page 8 - PARTS LIST; Qty Description
8 C3426M-A (5/07) PARTS LIST Qty Description 1 IS110 Series Camclosure integrated camera system • Cover and back box (assembled) • Trim ring with bubble; clear bubble models include a liner • Camera module 1 Black plug 1 1/8-inch hollow screwdriver bit 2 8-32 x 0.375-inch Phillips pan head screws wi...
Page 9 - SHOWN ACTUAL SIZE
C3426M-A (5/07) 9 Figure 1. Package Components COVER AND BACK BOX (1) CAMERA MODULE (1) TRIM RING, LINER, AND CLEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-INCH HOLLOW SCREWDRIVER BIT (1) BLACK PLUG (1) SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 0.75-INCH PHILLIPS PAN HEAD SCREWS (2) ...
Page 10 - Cover and Back Box Installation; BASIC SURFACE INSTALLATION; Voltage
10 C3426M-A (5/07) Cover and Back Box Installation The IS110 Series Camclosure integrated camera system mounts only to a surface. It can be wired through the cover into a surface, electrical box, or plaster ring. You can also wire it through a side conduit. UNSHIELDED TWISTED PAIR (UTP) VIDEO The IS...
Page 11 - S ELECTRICAL BOX INSTALLATION
C3426M-A (5/07) 11 8. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box...
Page 13 - 04 PLASTER RING INSTALLATION
C3426M-A (5/07) 13 404 PLASTER RING INSTALLATION NOTE: You should install the camera module into the back box before installing the back box into the cover. When installing the back box into the cover, rotate the camera module to access the mounting holes (refer to Camera Module on page 16 for more ...
Page 14 - SIDE CONDUIT INSTALLATION
14 C3426M-A (5/07) 5. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box...
Page 16 - MODULE REMOVAL
16 C3426M-A (5/07) Camera Module The IS110 Series Camclosure camera module includes the camera, camera bracket, and heater board. To perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module. MODULE REMOVAL...
Page 18 - CAMERA ORIENTATION; MODULE INSTALLATION
18 C3426M-A (5/07) CAMERA ORIENTATION At the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image could be upside down or sideways. To change the camera orientation (refer to Figure 8): 1. Remove the camera module...
Page 19 - Camera Adjustments; VARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS
C3426M-A (5/07) 19 Camera Adjustments To perform the following camera adjustments, make sure to plug in the camera and service connectors. You may have to remove the camera module from the back box. Connect a monitor. Then turn on power to the camera and monitor. To use the service connector, refer ...
Page 20 - DN/CH SERIES ADJUSTMENTS; SWITCH SETTINGS
20 C3426M-A (5/07) DN/CH SERIES ADJUSTMENTS Refer to Figure 10 to adjust the IS110-DN or IS110-CH model. Figure 10. Adjusting the IS110-DN/CH Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: AGC (Auto Gain Control) The AGC (automatic gain c...
Page 21 - AUTO IRIS LEVEL ADJUSTMENT
C3426M-A (5/07) 21 SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be caused by a number of conditions, including the quality of the source power and the age and type of fluorescent bulbs and ballasts. Set to ON to enable f...
Page 27 - VERTICAL PHASE ADJUSTMENT; Adjusting Vertical Phase; BLEMISH DETECTION
C3426M-A (5/07) 27 VERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 VAC operation only. When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one camera to another. To eliminate vertical roll, reverse the 24 VAC connections on one c...
Page 28 - Camera Positioning
28 C3426M-A (5/07) Camera Positioning Rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis in Figure 14). NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in damage to the wiring. Figure 14. Positioning the Came...
Page 29 - Install Liner and Trim Ring
C3426M-A (5/07) 29 Install Liner and Trim Ring 1. Adjust the liner if installed (refer to Figure 15): a. Align the screw holes in the trim ring with those in the back box to identify the proper liner position. b. Loosen the three Phillips screws located in the trim ring. c. Insert the blade of a sta...
Page 32 - Specifications; GENERAL
32 C3426M-A (5/07) Specifications GENERAL Pan/Tilt Adjustment Manual Pan 360° Tilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera mounting bracket and polycarbonate dome Cable Entry One 0.75-inch (1.91 cm) NPT threaded opening on side; two 0.75-inch (1.91 cm) openings ...
Page 35 - PRODUCT WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...