Pelco C3407M-D - Manuals

Pelco C3407M-D – Manual in PDF format online.

Manuals:

Manual

Manual Pelco C3407M-D

Summary

Page 3 - Contents; List of Illustrations

C3407M-D (1/07) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

4 C3407M-D (1/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 5 - Description; Qty Description; MODELS

C3407M-D (1/07) 5 Description The ICS150-CW Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor application...

Page 6 - SHOWN ACTUAL SIZE

6 C3407M-D (1/07) Figure 1. Package Components BACK BOX (1) CAMERA MODULE (1) TRIM RING, DOME LINER, AND CLEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-INCH HOLLOW SCREWDRIVER BIT (1) ADAPTER PLATE (1) SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 1.25-INCH PHILLIPS FLAT HEAD SCREWS (4) 8...

Page 7 - Cover and Back Box Installation; Voltage

C3407M-D (1/07) 7 Cover and Back Box Installation The ICS150-CW Series Camclosure integrated camera system mounts only into a wall or ceiling. UNSHIELDED TWISTED PAIR (UTP) VIDEO The ICS150-CW Series offers support for unshielded twisted pair (UTP). The UTP video output signal is 1 Vp-p differential...

Page 8 - SUSPENDED CEILING

8 C3407M-D (1/07) SUSPENDED CEILING NOTE: You should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera module to access the mounting holes. Refer to Camera Module on page 10 for more informati...

Page 9 - S DEEP ELECTRICAL BOX

C3407M-D (1/07) 9 4S DEEP ELECTRICAL BOX NOTE: You should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera module to access the mounting holes. Refer to Camera Module on page 10 for more info...

Page 10 - MODULE REMOVAL

10 C3407M-D (1/07) Camera Module The ICS150-CW Series Camclosure camera module includes the camera, camera bracket, and heater board. To perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module. MODULE REM...

Page 12 - CAMERA ORIENTATION; MODULE INSTALLATION

12 C3407M-D (1/07) CAMERA ORIENTATION At the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image will be upside down. To change the camera orientation (refer to Figure 7): 1. Remove the camera module from the bac...

Page 13 - Camera Adjustments; VARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS

C3407M-D (1/07) 13 Camera Adjustments To perform the following camera adjustments, make sure to plug in the camera and service connectors. You may have to remove the camera module from the back box. Connect a monitor. Then turn on power to the camera and monitor. To use the service connector, refer ...

Page 14 - SWITCH SETTINGS; SW3: Interlaced Scanning/Progressive Scanning

14 C3407M-D (1/07) SWITCH SETTINGS Locate the DIP switch (refer to Figure 9). Then set the switches for your installation. Figure 9. DIP Switch SW1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW2: Line Sync Set to ON to use AC line lock. Set to OFF for internal line sync...

Page 15 - Extended dynamic range:; VERTICAL PHASE ADJUSTMENT (24 VAC OPERATION ONLY); ADJUSTING THE VERTICAL PHASE

C3407M-D (1/07) 15 Extended dynamic range: Use for extremely high dynamic installations, for example, doorways, entrances, and exits. This profile offers the maximum wide dynamic range. Fluorescent: Use for any installation with flickering lighting of any kind. NOTE: If you select the Fluorescent pr...

Page 16 - Camera Positioning

16 C3407M-D (1/07) Camera Positioning Manually rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis in Figure 11). NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in damage to the wiring. Figure 11. Positioning...

Page 17 - Install Dome and Trim Ring

C3407M-D (1/07) 17 Install Dome and Trim Ring 1. Adjust the dome liner if installed (refer to Figure 12): a. Align the screw holes in the trim ring with those in the back box to identify the proper dome liner position. b. Loosen the three Phillips screws located in the trim ring. c. Insert the blade...

Page 20 - Specifications; CAMERA

20 C3407M-D (1/07) Specifications CAMERA Imaging Device 1/3-inch imager Dynamic Range 102 dB typical/120 dB maximum Picture Elements Sensor resolution: 742 (H) x 552 (V) Signal System NTSC or PAL Scanning System 2:1 interlace/progressive Synchronization Internal/AC line lock Horizontal Resolution Mo...

Page 21 - BACKBOX; Electrical

C3407M-D (1/07) 21 BACKBOX Electrical Input Voltage** 12 VDC or 24 VAC (±10%), autosensing Power Consumption 10 watts or less Video Connector Composite: BNCUTP: Twisted pair General Pan/Tilt Adjustment Manual Pan 360° Tilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera...

Page 23 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic ...