Pelco C2910M-C - Manuals - manualsarea.com

Page 3 - Contents

C2910M-C (4/06) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Cautions . . . . . . . . . . . . . . . . . . . . . ....

Page 6 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE; Cautions

6 C2910M-C (4/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 7 - Description; MODEL

C2910M-C (4/06) 7 Description The CCC5100H Series camera is a high resolution, 480 TV line, wide dynamic range video camera with a 1/3-inch SIMD imager. It automatically senses and sets the video standard to NTSC or PAL. It supports DC-drive auto iris lenses as well as C- and CS-mount lenses. The CC...

Page 9 - Lens Mounting; WIRING AN AUTO IRIS LENS; Pin

C2910M-C (4/06) 9 Lens Mounting The CCC5100H Series camera supports both manual and DC-drive auto iris lenses, either fixed focal length or varifocal. The camera accepts both CS- and C-mount lenses without a mount adapter. NOTE: The CCC5100H Series camera does not support video-drive auto iris lense...

Page 10 - Camera Mounting

10 C2910M-C (4/06) Camera Mounting The CCC5100H Series camera can be mounted from either the top or bottom, depending on the type of camera mount used in your installation. Use a standard 1/4-20 screw (provided) with a maximum thread length of 0.375 inch (10 mm). The optional Pelco PCM150 camera mou...

Page 11 - CONNECTING POWER; Wire Gauge

C2910M-C (4/06) 11 Power, Video, and Control Connections The CCC5100H Series is a low voltage camera. Maximum power consumption is about 4.5 watts. The CCC5100H Series camera offers standard power and coax video connectors as well as a multifunction connector that combines power, video (coax and uns...

Page 12 - USING COAX VIDEO; Maximum Distance

12 C2910M-C (4/06) USING COAX VIDEO The CCC5100H Series camera outputs coax video from either the BNC connector on the rear panel or through the multifunction connector. The camera also supports two Pelco up-the-coax technologies. Selected Pelco multiplexers and switchers send a Pelco V-Sync signal ...

Page 13 - USING THE MULTIFUNCTION CONNECTOR; By Pin

C2910M-C (4/06) 13 USING THE MULTIFUNCTION CONNECTOR The CCC5100H Series camera combines data, video, and power leads into a single multifunction connector on the rear panel. This lets you quickly install and uninstall the camera. NOTES: • Do not connect a network cable into the multifunction connec...

Page 14 - CONTROL LEADS; COAX VIDEO LEADS

14 C2910M-C (4/06) CONTROL LEADS The CCC5100H Series camera lets you access and configure the menu settings from any Pelco keyboard, receiver, or other device that supports the Pelco D or Pelco P protocol. The camera supports the following settings: • Baud rate: 2400, 4800, 9600 • Start bit: 1 • Dat...

Page 15 - POWER LEADS; USING THE SERVICE CONNECTOR; Receiver

C2910M-C (4/06) 15 UNSHIELDED TWISTED PAIR (UTP) LEADS The CCC5100H Series camera supports composite video over unshielded twisted pair (UTP) cabling. The camera UTP video output signal is 1 Vp-p differential into a 100-ohm load. At a minimum, UTP requires Cat5, 100-ohm twisted pair cable. You can i...

Page 16 - Setup Menus

16 C2910M-C (4/06) Setup Menus The CCC5100H Series camera uses setup menus instead of hardware switches for configuring the camera. As a result, you have more options for customizing the camera for its specific application. NOTE: After you customize any aspect of the CCC5100H Series camera, be sure ...

Page 18 - MENU ACTION

18 C2910M-C (4/06) ACCESSING THE SETUP MENUS (REAR PANEL) You can access and navigate the setup menus from the top, center, and bottom buttons on the rear panel (refer to Figure 6). Figure 6. Rear Panel Buttons These buttons respond differently to short and long presses. A short press is less than o...

Page 19 - ACCESSING THE SETUP MENUS (PELCO CONTROLLER); USING PRESET 95; PelcoNet

C2910M-C (4/06) 19 ACCESSING THE SETUP MENUS (PELCO CONTROLLER) USING PRESET 95 You can use preset 95 to access and navigate the setup menus from various Pelco controllers. Use the instructions for your controller to access the main menu. NOTE: CCC5100H Series camera operation has been verified for ...

Page 20 - NAVIGATING THE SETUP MENUS

20 C2910M-C (4/06) NAVIGATING THE SETUP MENUS As soon as you access the MAIN MENU, move the joystick up or down to select a menu option. Table J lists the buttons and actions for menu navigation. Table J. Pelco Controller Buttons and Actions NOTE: If your Pelco controller does not have a joystick, u...

Page 22 - Lens Type; LINE SYNCHRONIZATION; Line Sync; VIDEO LEVEL; Video Level

22 C2910M-C (4/06) Automatic (AGC) When configuring a DC-drive auto iris lens or when focusing the camera, you may have to temporarily enable or disable automatic gain control (AGC). The AGC feature automatically adjusts the image when the light level changes. AGC will be disabled for some procedure...

Page 23 - AUTO IRIS; DC Offset; FINE FOCUS

C2910M-C (4/06) 23 AUTO IRIS Use this menu to configure a DC-drive auto iris lens. For information on adjusting DC offset, refer to DC-Drive Auto Iris Lens Setup . NOTE: The CCC5100H Series camera does not support video-drive auto iris lenses. DC Offset Use this slider to adjust the camera’s DC volt...

Page 24 - CAMERA DISPLAY MENU; DISPLAY PROPERTIES

24 C2910M-C (4/06) CAMERA DISPLAY MENU Use the CAMERA DISPLAY menu to set camera identification information and to configure gamma, saturation, automatic gain control (AGC), and sharpness. Camera Name Enter the display name for this camera, one character at a time, up to 12 characters. The default i...

Page 25 - GAIN CONTROL; SHARPNESS

C2910M-C (4/06) 25 Manual Gamma Use this slider to either increase or decrease the amount of gamma correction. Move the slider from 25 to 100. The default depends on the selected profile (refer to Table K). Saturation Use this slider to either increase or decrease the amount of color in an image. Mo...

Page 26 - LIGHT METER MENU

26 C2910M-C (4/06) LIGHT METER MENU The CCC5100H Series camera uses light meter zones to adjust how it implements backlight compensation. Many installations include multiple light levels that make backlight compensation difficult. Use meter zones to correct this problem. Identify a specific light re...

Page 27 - WHITE BALANCE MENU; Mode

C2910M-C (4/06) 27 Active Zone Select the zone to enable: ZONE 1, ZONE 2, ZONE 3, or ZONE 4. The default zone is ZONE 2. You can activate only one zone at a time. Edit Zone Select the zone to define: EDIT ZONE 1, EDIT ZONE 2, EDIT ZONE 3, or EDIT ZONE 4. The zone edit screen appears, and the zone ha...

Page 28 - ATW NORMAL /ATW DESATURATION; MANUAL COLOR TEMPERATURE; Color Temp K

28 C2910M-C (4/06) ATW NORMAL /ATW DESATURATION Select this option to display the ATW NORMAL/DESAT menu. Use it to set the high and low temperature limits for the desired Auto Tracing White Balance (ATW) mode. NOTES: • The color temperature settings on this menu will apply to both ATW NORMAL and ATW...

Page 29 - PROFILES MENU; Default

C2910M-C (4/06) 29 PROFILES MENU Use the PROFILES menu to select or save a profile. Use profiles for faster installation or to quickly adjust camera settings for changing light conditions. The default is WDR. In addition to two user-definable profiles (CUSTOM1 and CUSTOM2), the CCC5100H Series camer...

Page 30 - INDOOR; OUTDOOR; WINDOW; GAMING

30 C2910M-C (4/06) Figure 9. Default Profile Scenes WDR (Wide Dynamic Range) : Select this profile for scenes that have both very bright and very dark areas. This profile emphasizes accurate light levels over color reproduction. HI-DEF (High Definition) : Select this profile for color- ful scenes th...

Page 31 - SYSTEM INFORMATION MENU; Restart Camera; Restore Factory Settings

C2910M-C (4/06) 31 SYSTEM INFORMATION MENU Use the SYSTEM INFORMATION menu to display the camera firmware information. Restart Camera Select this option to turn off the camera and then restart it. Restore Factory Settings Select this option to reset the camera to the factory default settings. This o...

Page 33 - Lens Setup and Focus Procedures; DC-DRIVE AUTO IRIS LENS SETUP

C2910M-C (4/06) 33 Lens Setup and Focus Procedures The following sections describe how to set up and focus the lens for your CCC5100H Series camera. DC-DRIVE AUTO IRIS LENS SETUP Before using a DC-drive auto iris lens, you must adjust the DC offset setting. Use the following steps to match the camer...

Page 35 - CAMERA FOCUSING; FIXED FOCAL LENS

C2910M-C (4/06) 35 CAMERA FOCUSING The CCC5100H Series camera features a fine focus screen that helps you focus your camera. Use it to adjust both the back focus (on the camera) and the fine focus (on the lens). Use the procedure specific for your lens. FIXED FOCAL LENS Use the following procedure t...

Page 36 - VARIFOCAL LENS

36 C2910M-C (4/06) 9. Manual iris only: Adjust the iris for the best picture quality. The largest aperture gives the best light sensitivity; the smallest aperture gives the greatest depth of field. 10. Tighten all lens locking screws. NOTE: When tightening the lens locking screws, do not over-turn o...

Page 40 - Predefined Profile Settings

40 C2910M-C (4/06) Predefined Profile Settings Table K lists the default settings that differ for each predefined profile. When configuring the CCC5100H Series camera, start with the profile that best fits your installation. After you customize it, save it into one of the user-definable profiles: CU...

Page 41 - Specifications; GENERAL

C2910M-C (4/06) 41 Specifications GENERAL Imaging Device 1/3-inch SIMD Dynamic Range 95 dB typical/120 dB maximum Picture Elements Sensor resolution: 742 (H) x 552 (V) Scanning System 525 (NTSC)/625 (PAL) lines, 2:1 interlace Synchronization Internal/ line lock/Pelco V-Sync Horizontal Resolution Mor...

Page 43 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic p...