Pelco C2495M-A - Manuals - manualsarea.com

Page 2 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

2 C2495M-A (1/06) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such...

Page 3 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

C2495M-A (1/06) 3 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 4 - Description

4 C2495M-A (1/06) Description Designed specifically for the MR5000 Series public viewing system, the ICS-DO111ABK integrated camera system packages a camera and lens into a small, discreet, high-security dome. Pelco’s MR5000 Series public viewing system is specifi cally designed for retail applicati...

Page 5 - Installation; PREPARE VIDEO AND ELECTRICAL CABLING

C2495M-A (1/06) 5 Installation PREPARE VIDEO AND ELECTRICAL CABLING 1. Temporarily remove the bottom end cap of the MR5000 Series mount if the end cap is installed. 2. Feed the 42-inch video cable (provided) through the monitor feedthrough hole in the mount arm and out the bottom end of the mount ar...

Page 8 - Install Camera; 2 VDC operation only:

8 C2495M-A (1/06) Install Camera 1. Some indoor installations do not require a heater. If the installation does not require a heater, remove the heater board from the camera assembly. To remove the heater press on an end of the board. 2. 12 VDC operation only: The camera is set for 24 VAC operation ...

Page 10 - Install Dome and Trim Ring

10 C2495M-A (1/06) Install Dome and Trim Ring 1. Align the screw holes in the trim ring with those in the Camclosure base. 2. Domes with Liners (only) – Position the viewing window over the lens of the camera by doing the following: a. Loosen the three Phillip screws located in the dome. b. Insert t...

Page 11 - AUTO IRIS LEVEL ADJUSTMENT

C2495M-A (1/06) 11 AUTO IRIS LEVEL ADJUSTMENT If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust the focus, it may be necessary to remove...

Page 12 - SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS; Manual backlight compensation:

12 C2495M-A (1/06) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fi xed lighting conditions where there...

Page 13 - SWITCH SETTINGS FOR VARIFOCAL LENS; AE Functions; Switch Number and Position

C2495M-A (1/06) 13 SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is confi gured at the factory for automatic exposure. For manually setting and locking the white balance, place a white background in front of camera and turn off switch 1. For gamma co...

Page 14 - Specifications; General

14 C2495M-A (1/06) Specifications General Operating Temperature -50° to 122°F (-46° to 50°C)De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fitting and 3/4-inch (1.91 cm) opening forNPT threaded pipe Pan/Tilt Adjustment Manual; 360° pan; 180° tilt Construction Aluminum with steel camer...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic...