Pelco C2461M-A - Manuals - manualsarea.com

Page 2 - CONTENTS; Section; LIST OF ILLUSTRATIONS; Figure

2 C2461M-A (7/03) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................... 3 WELCOME .....................................................................................................................................

Page 3 - C A U T I O N; IMPORTANT SAFEGUARDS AND WARNINGS; around the bolt holes between the enclosure and mounting surface.; REGULATORY NOTICES; • Reorient or relocate the receiving antenna.

C2461M-A (7/03) 3 Heater elements could be hot! When camera power is on, use cautionwhen adjusting the camera. C A U T I O N IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specif...

Page 4 - WELCOME; Thank you for purchasing Pelco’s Camclosure

4 C2461M-A (7/03) WELCOME Thank you for purchasing Pelco’s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology. Your new ICS150 Series in-ceiling dome system includes a high-resolution, low light, color camera with auto iris and varifocal lens. The LowLight ...

Page 5 - INSTALL THE BACK BOX; REMOVE THE LOWER DOME; Refer to Figure 1 for the following steps.; Voltage; Ground; AC Operation Only; – If you are wiring more than one Camclosure system to the same; Installation Directly to Wall/Ceiling

C2461M-A (7/03) 5 INSTALL THE BACK BOX REMOVE THE LOWER DOME Loosen the tamper-resistant screws with the supplied 1/8-inch hollow screwdriver bit. Remove thelower dome and place it to the side. INSTALL THE BACK BOX The installation methods for the ICS150 back box include the following: • Attach Dire...

Page 6 - Attach to a 4S Deep Electrical Box

6 C2461M-A (7/03) Attach to a 4S Deep Electrical Box Refer to Figure 2 for the following steps. The installation instructions assume that the 4S box waspreviously installed. 1. Attach adapter plate to the 4S box with the two 8-32 x .750-inch screws supplied. 2. Connect the video cable. 3. Connect th...

Page 7 - Install in a Ceiling Tile; Refer to Figure 3 for the following steps.

C2461M-A (7/03) 7 Install in a Ceiling Tile Refer to Figure 3 for the following steps. 1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Use the adapter plate as a template. 2. Punch four screw holes in the ceiling tile. Use the four threaded screw holes in the adapte...

Page 8 - Heater Jumper and Camera Connector Locations; INSTALL THE CAMERA MODULE; CHECK HEATER JUMPER

8 C2461M-A (7/03) Figure 4. Heater Jumper and Camera Connector Locations INSTALL THE CAMERA MODULE CHECK HEATER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not requirethis heater. If the unit will never be subjected to a frost temperature, you can disa...

Page 9 - Wall Mounting; Ceiling Mounting; - The camera bracket tab; INSTALL AND POSITION THE CAMERA

C2461M-A (7/03) 9 Wall Mounting - The camera bracket tab points out of the enclosure and the top of thecamera points up towards the tab. Ceiling Mounting - The camera bracket tab points out of the enclosure and the top of thecamera is pointed in the opposite direction. CAMERA BRACKETTAB ALWAYS POINT...

Page 10 - Default Switch Settings and Location of Camera Adjustments; MAKE CAMERA SETTINGS

10 C2461M-A (7/03) Figure 5. Default Switch Settings and Location of Camera Adjustments ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring clockwise/counterclockwise. Refer to Figure 5. 2. Tighten the zoom locking screw. 3. Adjust the focus by moving the focus locking screw clo...

Page 11 - ON

C2461M-A (7/03) 11 ON OFF DIGITAL SLOW SHUTTER (DSS) Digital slow shutter slows the picture frame rate and increases the camera sensitivity under lowlight conditions. Depending on the number of fields of integration the picture will develop agranular appearance and motion may show some lag, resultin...

Page 12 - reference camera selected in step 1.; VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT

12 C2461M-A (7/03) VERTICAL PHASE ADJUSTMENT (24 VAC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitorwhen a camera view is switched. To eliminate vertical roll reverse the 24 VAC connections on onecamera. If both cameras are connected to th...

Page 13 - Dome and Trim Ring Installation; REINSTALL THE DOME AND TRIM RING

C2461M-A (7/03) 13 Figure 6. Dome and Trim Ring Installation REINSTALL THE DOME AND TRIM RING Place the trim ring and dome over the back box. If the dome has a liner, position the viewing windowover the lens of the camera. Tighten the tamper-resistant screws with the supplied 1/8-inch hollowscrewdri...

Page 14 - SPECIFICATIONS; BACKBOX

14 C2461M-A (7/03) SPECIFICATIONS BACKBOX Electrical Input Voltage: 12 VDC or 24 VAC, ± 10%, auto-sensing Power Consumption: 13 watts or less Video Connector: BNC General Operating Temperature: -50 ° to 122 ° F (-46 ° to 50 ° C) De-ices to 25 ° F (-4 ° C) Pan/Tilt Adjustment: Manual; 360 ° pan; 180 ...

Page 15 - REVISION HISTORY; WARRANTY AND RETURN INFORMATION

C2461M-A (7/03) 15 REVISION HISTORY Manual # Date Comments C2461M 4/03 Preliminary manual for beta testing. C2461M-A 7/03 Final version. ® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. WARRANTY ...