Pelco C2423M - Manuals

Pelco C2423M – Manual in PDF format online.

Manuals:

Manual

Manual Pelco C2423M

Summary

Page 2 - CONTENTS; Section

CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3OPERATION ...................................................................................................................... 4 POWER-UP DISPLAY .................................

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; MEASURES DE SECURITE IMPORTANTES; électrique est présant dans cette unité.

IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R,...

Page 4 - OPERATION; Protocol C; OPERATING YOUR SPECTRA II COLOR/BLACK & WHITE DOME

OPERATION POWER-UP DISPLAY When the Spectra II™ dome is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the...

Page 6 - The dome cannot; PATTERNS

NOTE: The dome cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern. PATTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt or lens com...

Page 7 - Park; IR FILTER; Hold down the Iris Open button until the iris is wide open.

AUXILIARY OUTPUTS An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay. The relay will remain latched until a clear command is issued. An AUX 2 command from the controller will place a ground at the output of AUX 2 to operate ...

Page 8 - PROGRAMMING; For detailed instructions, refer to the following sections.; MAIN MENU

PROGRAMMING Programming Guide - Spectra II Color/Black & White Gain/AGC Menu 1. Access main menu (preset 95). 2. Make main menu selections. Joystick: Move up or down to position cursor or to toggle between selections. Iris Open: Enter Iris Close: Cancel PRESETS The following presets are reserved...

Page 10 - ALARMS

NOTE: Pattern length is set on the secondary menu entitled Other. NOTE: To make the pattern run to its end when an alarm activates it, make alarm dwell time longer than pattern length. Thus, if the alarm goes away before the end of the pattern, the pattern will continue until the dwell times out. AL...

Page 11 - The Spectra II; ALARM PRIORITY

NOTE: The Spectra II Color/Black and White camera cannot do electronic zoom in a pattern. Optical zoom will operate in a pattern. 6. Position the cursor (>) beside the number of the alarm input for which you want to set the pattern. 7. Press the Iris Open button. The cursor moves to the right, be...

Page 12 - Auto focus is auto

AUTO FLIP Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu Auto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min Exit There are two auto flip modes: On - Auto fli...

Page 13 - AUTO IRIS; The following are the settings for auto iris:

AUTO IRIS Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Auto-Iris Menu Auto-iris mode Auto Auto-iris level 7 Exit Camera Menu Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Th...

Page 14 - AUTO IR LEVEL; /60 second shutter speed; Slow shutter operation affects the auto IR level setting.; Slow Shutter Mode section.; AUX MODE

AUTO IR LEVEL Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> E...

Page 15 - If backlight; in; condi; BACKLIGHT COMPENSATION

NOTE: If backlight compensation is ON and the IR cut filter switches OUT (black and white mode) in normal lighting condi tions, adjust the Auto IR Level to a darker setting. Refer to the Auto IR Level section. 4. Move the joystick up or down to position the cursor next to either Aux 1 mode or Aux 2...

Page 16 - AGC MODE; GAIN; Press the Iris Open button to enter the Camera menu.

GAIN/AGC Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Camera Menu Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Gain/AGC Menu AGC mode Auto Gain 6 Exit Gain - The amount of ...

Page 17 - IR FILTER MODE; CAMERA SETTING; LIMIT STOPS

IR FILTER MODE Main Menu Camera Menu Next Menu IR Filter Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> ...

Page 18 - Programming; TURNING LIMIT STOPS ON OR OFF; Press the Iris Open button to enter the Other menu.; Scan Limit Stops; Make sure limit stops are turned ON, and then exit the menu.; LINE SYNCHRONIZATION

NOTE: Programming preset 90 (23) disables the manual limit stops until preset 91 (24) is set. NOTE: On power-up, the auto scan tilt angle will be whatever angle the camera was at when the right scan limit was set. TURNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28)...

Page 19 - PARK TIME MINUTES; Preset 1 must be; PATTERN LENGTH; The Spectra II dome can do the following:; If the

LINE SYNC PHASE - The cursor moves to a numeric value. Move the joystick up or down to change the value. Press the Iris Open button to select the choice. The value represents the phase angle in tenths of a degree between 0 degrees and 359 degrees. For example, 900 is 90 degrees, 1200 is 120 degrees,...

Page 20 - PROPORTIONAL PAN; There are two proportional pan modes:

POWER-UP MODE Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Power-Up Menu Power Up Default Exit This feature lets the dome resume a desired condition following power-up. The menu includes the following choices. Default - On powe...

Page 21 - RESET CAMERA

3. Press the Iris Open button to enter the Other menu. 4. Position the cursor (>) beside Proportional Pan. 5. Press the Iris Open button. The cursor moves to the right, beside the word On or Off. 6. Move the joystick up or down to toggle between On and Off. 7. SELECT - Press the Iris Open button ...

Page 22 - SCAN SPEED; SHARPNESS; Do the following to manually adjust the sharpness of the picture:

SCAN SPEED Main Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Other Menu Auto flip On Proportional pan On Limit stops Off Park time minutes 0 Scan speed deg/s 25 Pattern length 1.5 min Exit The scan speed is adjustable from 1-40 degr...

Page 23 - SHUTTER SPEED; There are several electronic shutter speed settings:

SHUTTER SPEED Main Menu Camera Menu Next Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Slow shutter mode Auto Shutter speed Auto Auto...

Page 24 - SLOW SHUTTER MODE; There are two settings in the slow shutter mode:

SLOW SHUTTER MODE Main Menu Camera Menu Next Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Backlight comp Off Zoom limit x72 Reset camera <Gain/AGC> <Auto-iris> <Next> Exit Slow shutter mode Auto Shutter speed Auto ...

Page 25 - WHITE BALANCE; RED BALANCE and BLUE BALANCE LEVELS -; ZONES

WHITE BALANCE Main Menu Camera Menu Next Menu White Balance Menu Slow shutter mode Auto Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Previous Exit <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other&g...

Page 26 - ZONE BLANK; Press the Iris Open button to enter the Alarms, Zone Blank menu.; ZOOM LIMIT

ZONE BLANK Main Menu Alarms, Zone Blank Menu Zone Blank Menu <Camera> <Line Sync> <Power Up> <Aux> <Alarms, Zone Blank> <Other> EXIT Alarm resume Off Alarm dwell sec 5 <Alarm priority> <Alarm pattern> <Zone blank> Exit Video Blank Zone 1Off 2Off ...

Page 27 - MAINTENANCE; DOME CLEANING; SERVICE MANUAL; SPECIFICATIONS; MECHANICAL; CAMERA

MAINTENANCE DOME CLEANING Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome’s exterior surface with a nonabrasive cleaning cloth and cleaning agent that is safe for acrylic. Either liquid or spray cl...

Page 28 - REVISION HISTORY

Effective Pixels NTSC: 768 (H) x 494 (V) PAL: 752 (H) x 582 (V) Horizontal Resolution: >470 TV lines Lens Minimum f-stop: F1.4 Focal Length: 4.1 mm to 73.8 mm optical Zoom Ratio: 18X optical zoom, 4X electronic zoom Digital Slow Shutter: Auto/manual speed selection Horizontal Angle of View: 48 ° ...