Pelco C2410M-J - Manuals - manualsarea.com

Page 2 - Contents

2 CxxxxM (xx/08) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - Important Safety Instructions

C2410M-J (2/08) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such...

Page 4 - Regulatory Notices; Radio and Television Interference

4 C2410M-J (2/08) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 5 - Description; Installation; INSTALL BACK BOX; MOUNTING DIRECTLY TO A WALL OR CEILING

C2410M-J (2/08) 5 Description The 150 Series Camclosure ® integrated camera system is an in-ceiling dome incorporating a camera and lens package into a small, discreet, high-security enclosure designed for areas subject to heavy vandalism. The system is perfect for a variety of indoor and outdoor ap...

Page 6 - INSTALL CAMERA; 2 VDC Operation Only:

6 C2410M-J (2/08) MOUNTING TO CEILING TILE 1. Remove the ceiling tile. 2. Using the adapter plate as a template, cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile for the back box. Punch four screw holes in the ceiling tile. 3. Attach the back box to the ceiling tile and adapter plate wit...

Page 7 - INSTALL DOME AND TRIM RING

C2410M-J (2/08) 7 3. If the heater is installed, plug the heater connector from the camera into the mating connector inside the base. Plug the video connector from the camera into the mating connector inside the base. Turn on power to the camera and monitor. 4. Always make sure the tab on the camera...

Page 8 - Adjustments

8 C2410M-J (2/08) Adjustments The camera is set up at the factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. 1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, focus, or switch settings (refe...

Page 9 - Specifications; GENERAL

C2410M-J (2/08) 9 Specifications GENERAL Operating Temperature -50° to 122°F (-46° to 50°C)De-ices to 25°F (-4°C) Pan/Tilt Adjustment Manual; 360° pan, 180° tilt Construction Aluminum with steel camera mounting bracket and polycarbonate dome Finish White polyester powder coat trim ring with charcoal...

Page 10 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...

Page 11 - REVISION HISTORY

C2410M-J (2/08) 11 REVISION HISTORY Manual # Date Comments C2410M 11/99 Original version. C2410M 1/00 Revised installation instructions. Added FCC notices. C2410M-A 1/00 Added varifocal lens. Changed format. C2410M-B 7/00 Added information on dome liner. C2410M-C 1/01 Added heater element caution. C...