Pelco C2410M-H - Manuals - manualsarea.com

Page 2 - Installation; 50 Series Camclosure

Installation 150 Series Camclosure ® Integrated Camera System C2410M-H (10/05) Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com USA and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120

Page 3 - CONTENTS; Section

[ 2 ] Pelco Manual C2410M-H (10/05) CONTENTS Section Page IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................ 3 REGULATORY NOTICES .........................................................................................

Page 4 - RADIO AND TELEVISION INTERFERENCE

Pelco Manual C2410M-H (10/05) [ 3 ] IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.6. Do not install near any heat...

Page 5 - DESCRIPTION; Install Back Box; Mounting Directly to Wall or Ceiling; INSTALLATION

[ 4 ] Pelco Manual C2410M-H (10/05) DESCRIPTION The 150 Series Camclosure ® Integrated Camera System is an in-ceiling dome incorporating a camera and lens package into a small, discreet, high-security enclosure designed for areas subject to heavyvandalism. 1 Install Back Box Mounting Directly to Wal...

Page 6 - Mounting to 4S Deep Electrical Box; Install Camera; C A U T I O N

Pelco Manual C2410M-H (10/05) [ 5 ] 8.32 X .750 SCREW(SUPPLIED) 8.32 X .375 SCREW(SUPPLIED) WALL ORCEILING ADAPTER PLATE BACK BOX 4S DEEPELECTRICALBOX 01063 CEILING TILE BACK BOX ADAPTER PLATE 8-32 X 1.25MOUNTINGHARDWARE(SUPPLIED) 01062 Mounting to 4S Deep Electrical Box 1. Attach adapter plate to t...

Page 7 - Wall Mounting; Ceiling Mounting

[ 6 ] Pelco Manual C2410M-H (10/05) 24 VAC JUMPER 12 VDC JUMPER VIDEOCONNECTOR HEATERCONNECTOR 01065 VIDEOCONNECTOR HEATERCONNECTOR 01068 CAMERA BRACKETTAB ALWAYS POINTSOUT OF THEENCLOSURE 01071 CAMERA BRACKETTAB ALWAYS POINTSOUT OF THEENCLOSURE TOP OFCAMERA 01086 Wall Mounting - The camera bracket ...

Page 8 - Install Dome and Trim Ring

Pelco Manual C2410M-H (10/05) [ 7 ] ADJUSTMENTS (COLOR CAMERA ONLY) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes,however, adjustments may be necessary. 1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit. 2. A...

Page 9 - Focus Adjustment for Fixed Focal Length Lens with Auto Iris; Auto Iris Level Adjustment

[ 8 ] Pelco Manual C2410M-H (10/05) Focus Adjustment for Fixed Focal Length Lens with Auto Iris To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screwon the bottom of the lens. To remove the heater board: 1. Disconnect the four-pin heater wiring.2. W...

Page 10 - Switch Settings for Fixed Focal Length Lens Without Auto Iris

Pelco Manual C2410M-H (10/05) [ 9 ] NOT USED = SWITCH POSITION FACTORY SETTINGS ALC Y BLC ABL ELC DC OFF OFF 01061 ON OFF Switch Settings for Fixed Focal Length Lens Without Auto Iris Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation(factory settin...

Page 11 - Switch Settings for Varifocal Lens; For gamma correction

[ 10 ] Pelco Manual C2410M-H (10/05) Switch Settings for Varifocal Lens The high resolution camera withvarifocal lens and auto iris isconfigured at the factory foroptimal performance in lightingconditions where auto iris isrequired. It is also configured withthe shutter speed set at 1/60(NTSC) or 1/...

Page 12 - SPECIFICATIONS; General

Pelco Manual C2410M-H (10/05) [ 11 ] REVISION HISTORY Manual # Date Comments C2410M 11/99 Original version. C2410M 1/00 Revised installation instructions. Added FCC notices. C2410M-A 1/00 Added varifocal lens. Changed format. C2410M-B 7/00 Added information on dome liner. C2410M-C 1/01 Added heater ...

Page 13 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after thedate of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic ...