Pelco C2407M-G (5/03) - Manuals

Page 3 - CONTENTS; Section

Pelco Manual C2407M-G (5/03) [ 3 ] CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................... 4 DESCRIPTION ................................................................................................................

Page 4 - The 100 Series Camclosure; INSTALLATION; Install Base; Mounting Directly to Wall or Ceiling; Cut a small hole in the ceiling or wall for; I M P O R T A N T

[ 4 ] Pelco Manual C2407M-G (5/03) IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all localcodes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it isdesigned for indoor ...

Page 5 - Connect Video and Power; 2 VDC Operation Only –

Pelco Manual C2407M-G (5/03) [ 5 ] CONDUIT PLUG CONCRETE WALLOR CEILING MOUNTINGHARDWARE(NOT SUPPLIED) BASE SET SCREW 8-32 X .750 FLAT HEADSCREW (SUPPLIED) 8-32 X .375 PAN HEADSCREW (SUPPLIED) WALL ORCEILING ADAPTER PLATE BASE 4S ELECTRICALBOX SCREW (SUPPLIED);SEE TEXT FOR SIZE WALL ORCEILING 401 OR...

Page 6 - Install Camera; C A U T I O N; Wall Mounting –

[ 6 ] Pelco Manual C2407M-G (5/03) 3 Install Camera 1. Some indoor installations do not require a heater. If theinstallation does not require a heater, remove the heaterboard from the camera assembly. To remove the heaterapply pressure and press on the corner of the board. 2. If the heater is instal...

Page 7 - Install Dome and Trim Ring; Align the screw holes in the trim ring with

Pelco Manual C2407M-G (5/03) [ 7 ] ADJUSTMENTS (COLOR CAMERA ONLY) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes,however, adjustments may be necessary. 1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit. 2. Ad...

Page 8 - To remove the heater board:; Auto Iris Level Adjustment

[ 8 ] Pelco Manual C2407M-G (5/03) Focus Adjustment for Fixed Focal Length Lenswith Auto Iris To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screwon the bottom of the lens. To remove the heater board: 1. Disconnect the four-pin heater wiring.2. Wai...

Page 10 - SPECIFICATIONS; Switch Settings for Varifocal Lens; CAUTION; AE Functions

[ 10 ] Pelco Manual C2407M-G (5/03) SPECIFICATIONS General OperatingTemperature: -50 ° to 122 ° F (-46 ° to 50 ° C) De-ices to 25 ° F (-4 ° C) Cable Entry: 3/4-inch (1.91 cm) conduit fittingand 3/4-inch (1.91 cm) openingfor NPT threaded pipe Pan/TiltAdjustment: Manual; 360 ° pan; 180 ° tilt Construc...

Page 11 - Regulator y Notices; Reorient or relocate the receiving antenna.; REVISION HISTORY

Pelco Manual C2407M-G (5/03) [ 11 ] Regulator y Notices FCC Class A (monochrome, EIA and CCIR cameras – exceptauto iris models) This equipment has been tested and found to comply with the limits of a Class A digital device, pursuantto part 15 of the FCC rules. These limits are designed to provide re...

Page 12 - PRODUCT WARRANTY AND RETURN INFORMATION

[ 12 ] Pelco Manual C2407M-G (5/03) Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, and Camclosure are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or...