Pelco C2406M-F - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS AND WARNINGS; operating instructions unless you are qualified to do so.

2 C2406M-F (4/04) IMPORTANT SAFEGUARDS AND WARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources ...

Page 3 - DESCRIPTION; The wedge style 200 Series Camclosure

C2406M-F (4/04) 3 DESCRIPTION The wedge style 200 Series Camclosure ® integrated camera system is designed to mount directly to a wall or ceiling. It also can mount to a corner with the ICS200-CM corner mount. The systemincorporates a camera and lens package into a small, medium security enclosure.

Page 4 - INSTALLATION; PREPARE MOUNTING SURFACE; Outdoor Installation –; Removing Camera Module

4 C2406M-F (4/04) INSTALLATION The following parts are supplied: 1 Camclosure integrated camera system 1 Watertight mounting plate 1 1/8-inch pin-in-hex Allen wrench bit 3 10-32 x 0.5-inch Phillips screws 3 #10 internal tooth lock washers 1 Hole plug PREPARE MOUNTING SURFACE 1. Remove the cover of t...

Page 5 - INSTALL BASE; WITHOUT CONDUIT; Voltage Jumper Settings; WITH CONDUIT; Outdoor Installation Only –; Install Hole Plug

C2406M-F (4/04) 5 INSTALL BASE WITHOUT CONDUIT 1. Outdoor Installation Only – Bring the power and video wiring for the camera through the wiring hole in the watertight mounting plate. Then fasten the mounting plate to the mountingsurface with #8 stainless steel screws (not provided) of the appropria...

Page 6 - Base Installation with Conduit

6 C2406M-F (4/04) bottom of the base (refer to Figure 5). Pull thewiring inside the base. WARNING: Be careful not to damage the wiring or the connection where thevideo cable is fastened to the circuitboard. 3. Using the screwdriver bit that is provided, remove the conduit cover and plate by unscrewi...

Page 7 - REINSTALL CAMERA MODULE; Camera Installation; ADJUST POSITION; Varifocal Lens Only –; REPLACE COVER; VARIFOCAL LENS; Adjustable Mounting Pattern

C2406M-F (4/04) 7 REINSTALL CAMERA MODULE 1. Reinstall the camera module. Refer to Figure 8. Make sure the top of the camera is oriented properly. On the lens housing, look for the label that says TOP. WARNING: To prevent damage to the camera or lens, the camera must be installed in the proper hole ...

Page 8 - Vertical Phase Adjustment; AUTO IRIS LEVEL ADJUSTMENT; Iris Level Adjustment; FIXED LENS

8 C2406M-F (4/04) ADJUSTMENTS (COLOR CAMERA ONLY) If you have a color camera, it is set up at the factory and normally requires no adjustments.Sometimes, however, adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iris ...

Page 9 - FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS; C A U T I O N; Removing Heater Board

C2406M-F (4/04) 9 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust the focus, do the following: 1. Loosen the locking screw on the bottom of the lens. To loosen the screw, it may be necessary toremove the heater board. Refer to Figure 14 andthe accompanying steps. 2. Move the sc...

Page 10 - SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS; SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS

10 C2406M-F (4/04) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to Figure 16. The switch is located next to the lens. Automatic backlight compensation(factory setting) is used under varying lighting conditions (such as outdoors) or fixed lightingconditions where there are no b...

Page 11 - SWITCH SETTINGS FOR VARIFOCAL LENS; To enable automatic exposure; CAUTION; Shutter; AE Functions; Switch Settings for Varifocal Lens

C2406M-F (4/04) 11 SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camerawith varifocal lens andauto iris is configured atthe factory for optimalperformance in lightingconditions where auto irisis required. It is alsoconfigured with the shutterspeed set at 1/60 (NTSC) or1/50 (PAL) and AGC set...

Page 12 - SPECIFICATIONS; General

12 C2406M-F (4/04) (Design and product specifications subject to change without notice.) SPECIFICATIONS General Pan/Tilt Adjustment: Manual; ± 10 ° pan; 5 ° above horizontal to 20 ° below horizontal tilt; additional 24 ° pan adjustment when installing using the adjustable mounting pattern in base Ra...

Page 13 - REGULATORY NOTICES; • Reorient or relocate the receiving antenna.

C2406M-F (4/04) 13 REGULATORY NOTICES FCC Class A (monochrome, EIA cameras only) This equipment has been tested and found to comply with the limits of a Class A digital device,pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protectionagainst harmful interference...

Page 14 - WARRANTY AND RETURN INFORMATION

14 C2406M-F (4/04) WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date ofshipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured...

Page 15 - REVISION HISTORY

C2406M-F (4/04) 15 REVISION HISTORY Manual # Date Comments C2406M 11/99 Original version. 1/00 Revised installation instructions. Added FCC notices. C2406M-A 2/00 Added varifocal lens. Changed format. C2406M-B 11/00 New camera module design, revised installation instructions. C2406M-C 1/01 Revised h...