Pelco C2404M-A - Manuals - manualsarea.com

Page 2 - Contents

2 C2404M-A (4/05) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

C2404M-A (4/05) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the ma...

Page 4 - REGULATORY NOTICES; RADIO AND TELEVISION INTERFERENCE

4 C2404M-A (4/05) REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 5 - Welcome

C2404M-A (4/05) 5 Welcome Thank you for purchasing Pelco’s Camclosure ® integrated camera system with LowLight ™ , DSS (digital slow shutter) technology. Your new ICS110 Series surface mount dome system includes a high resolution, low light, color camera with auto iris and varifocal lens. The LowLig...

Page 6 - Installation; MOUNTING DIRECTLY TO SURFACE; WIRING THROUGH BASE

6 C2404M-A (4/05) Installation MOUNTING DIRECTLY TO SURFACE WIRING THROUGH BASE Follow the proceeding steps when feeding wire/cables through the base of the cover and back box: 1. Using the cover as a template, mark one of the large hole positions onto the mounting surface. 2. Cut out the hole in th...

Page 7 - WIRING THROUGH SIDE CONDUIT; MOUNTING TO A 4S ELECTRICAL BOX; MOUNTING TO A PLASTER RING

C2404M-A (4/05) 7 WIRING THROUGH SIDE CONDUIT Follow the proceeding steps when feeding wire/cables through the side conduit opening of the unit: 1. Attach the cover to the mounting surface (hardware not supplied). Use stainless steel hardware when installing the system outdoors. 2. Remove the condui...

Page 8 - Install the Camera Module; CHECK HEATER JUMPER

8 C2404M-A (4/05) Install the Camera Module CHECK HEATER JUMPER The Camclosure is equipped with a heater to defrost the dome. Some installations may not require this heater. If the unit will never be subjected to a frost temperature, you can disable the heater, saving power. To disable the heater, r...

Page 9 - INSTALL AND POSITION THE CAMERA; Wall Mounting; Ceiling Mounting

C2404M-A (4/05) 9 INSTALL AND POSITION THE CAMERA 1. Plug the video connector from the camera into the mating connector inside the back box. 2. Position the camera so that the tab on the camera bracket is pointing out of the enclosure, away from the ceiling or wall. Refer to the following illustrati...

Page 10 - MAKE CAMERA SETTINGS; ON OFF

10 C2404M-A (4/05) MAKE CAMERA SETTINGS ZOOM/FOCUS 1. Select a field of view by turning the zoom adjustment ring. 2. Tighten the zoom locking screw. 3. Adjust the focus by moving the focus locking screw clockwise/counterclockwise. 4. Tighten the focus locking screw. DIGITAL SLOW SHUTTER (DSS) Digita...

Page 11 - OFF; VERTICAL PHASE ADJUSTMENT (24 VAC OPERATION ONLY); VARIFOCAL LENS AUTO IRIS LEVEL ADJUSTMENT

C2404M-A (4/05) 11 AGC (AUTOMATIC GAIN CONTROL) AGC automatically adjusts the image to compensate for changes in light levels. ON (Default setting) – Enables the AGC mode. OFF – Disables the AGC mode. BLC (BACK LIGHT COMPENSATION) The BLC (backlight compensation) feature compensates for backlit scen...

Page 12 - Install Dome and Trim Ring

12 C2404M-A (4/05) Install Dome and Trim Ring 1. Domes with Liners: Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard screwdriver in one of the adjustment grooves. Move the dome into position. c. Tighten...

Page 13 - Specifications; Backbox

C2404M-A (4/05) 13 Specifications Backbox ElectricalInput Voltage 12 VDC or 24 VAC, ±10%, auto-sensing Power Consumption 13 watts or less Video Connector BNC GeneralOperating Temperature -50° to 122°F (-46° to 50°C)De-ices to 25°F (-4°C) Pan/Tilt Adjustment:Manual 360° pan; 180° tilt Construction Al...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic...