Pelco C2403M-E (2/08) - Manuals

Page 3 - Contents

C2403M-E (2/08) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

4 C2403M-E (2/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such...

Page 5 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

C2403M-E (2/08) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 6 - Description

6 C2403M-E (2/08) Description The ICS110 Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications, ...

Page 7 - Installation; MOUNTING DIRECTLY TO SURFACE; WIRING THROUGH BASE

C2403M-E (2/08) 7 Installation MOUNTING DIRECTLY TO SURFACE WIRING THROUGH BASE Follow the proceeding steps when feeding wire/cables through the base of the cover and back box: 1. Using the cover as a template, mark one of the large hole positions onto the mounting surface. 2. Cut out the hole in th...

Page 8 - WIRING THROUGH SIDE CONDUIT; MOUNTING TO A 4S ELECTRICAL BOX; MOUNTING TO A PLASTER RING

8 C2403M-E (2/08) WIRING THROUGH SIDE CONDUIT Follow the proceeding steps when feeding wire/cables through the side conduit opening of the unit: 1. Attach the cover to the mounting surface (hardware not supplied). Use stainless steel hardware when installing the system outdoors. 2. Remove the condui...

Page 9 - Install Camera

C2403M-E (2/08) 9 Install Camera 1. Some indoor installations do not require a heater. If the installation does not require a heater, remove the heater board from the camera assembly. To remove the heater, press on an end of the board. 2. 12 VDC operation only: The camera is set for 24 VAC operation...

Page 10 - Install Dome and Trim Ring

10 C2403M-E (2/08) Install Dome and Trim Ring Domes with Liners (only): 1. Align the screw holes in the trim ring with those in the Camclosure base. 2. Position the viewing window over the lens of the camera. a. Loosen the three Phillip screws located in the dome. b. Insert the blade of a standard s...

Page 11 - Adjustments

C2403M-E (2/08) 11 Adjustments The camera is set up at the factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. 1. Remove the dome and trim ring using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, focus, or switch settings (ref...

Page 13 - Specifications

C2403M-E (2/08) 13 Specifications General Operating Temperature -50° to 122°F (-46° to 50°C)De-ices to 25°F (-4°C) Cable Entry 3/4-inch (1.91 cm) conduit fitting and 3/4-inch (1.91 cm) opening for NPT threaded pipe Pan/Tilt Adjustment Manual; 360° pan, 180° tilt Construction Aluminum with steel came...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...