Pelco c1943m - Manuals

Pelco c1943m – Manual in PDF format online.

Manuals:

Manual

Manual Pelco c1943m

Summary

Page 2 - CONTENTS; Section; LIST OF ILLUSTRATIONS; Figure

2 Pelco Manual C1943M (9/99) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 DESCRIPTION ................................................................................................................... 3 MODELS ..............

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; DESCRIPTION; Currently the

Pelco Manual C1943M (9/99) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and con-form to all local codes. 2. Unless the unit is specificall...

Page 4 - PRE-INSTALLATION INFORMATION; FRONT VIEW; Figure 2. Front Panel Removal

4 Pelco Manual C1943M (9/99) MODELS CM9760-VCRC-P VCR control unit capable of controlling 64 VCRs per unit. VCRcontrol is specific to Pelco TLR2096. OPTIONS CM9760-VCRC-PTX A 50-foot (15.2 m) VCR control cable with 1/8-inch jack on oneend (for connecting to VCR) and cord/shield (signal/ground) barew...

Page 5 - DIP SWITCHES; Figure 3 identifies the relative locations of DIP switches 1 and 2.; LEDs; Figure 3. DIP Switch Location

Pelco Manual C1943M (9/99) 5 DIP SWITCHES With the front panel removed, DIP switch 1 and DIP switch 2 are visible. These twoten-position DIP switches configure and define many functions of the CM9760-VCRC-P. Figure 3 identifies the relative locations of DIP switches 1 and 2. DIP switch functions are...

Page 6 - REAR VIEW; One DB-9 type connector for factory use only

6 Pelco Manual C1943M (9/99) REAR VIEW The rear of the unit is illustrated in Figure 4. From left to right are the following: 1. The four 16-input blocks of VCR connectors in the form of screw-type connectors withassociated mating plugs (one shown in Block 1) running from the left rear to middlerigh...

Page 7 - INPUT VCR CONNECTORS; Figure 5. VCR Input Plugs

Pelco Manual C1943M (9/99) 7 INPUT VCR CONNECTORS Physically, each of the four VCRC-P input connectors consists of the same number of inputscrew-type terminals. Each input group uses a dual-row removable plug and each plug isassociated with 8 VCR inputs. For example, refer to the leftmost group repr...

Page 8 - Figure 6. Relay Output Connector

8 Pelco Manual C1943M (9/99) RELAY OUTPUT CONNECTOR Figure 6 illustrates the relay output connector and its relative port pin assignments. Theconnector is a three-position plug with screw-type contacts similar in operation to the mat-ing connectors just discussed. By default, the relay is in its nor...

Page 9 - The DB-9 connector is reserved for factory use only.

Pelco Manual C1943M (9/99) 9 DB-9 Connector Pin-outs The DB-9 connector is reserved for factory use only. RJ-45 Connector RJ-45 connector pin-outs are illustrated in Figure 7. Because both RJ-45 connectors have the same wiring pin-outs, they require the same“flipped” cable. In other words, the IN co...

Page 10 - POWER CONNECTIONS; Figure 9. Power Input Fuse Replacement

10 Pelco Manual C1943M (9/99) POWER CONNECTIONS The CM9760-VCRC-P utilizes an auto-ranging internal transformer circuit that allows the in-put power to range from 100-240 VAC @ 50/60 Hz. Associated with the input power is thepower ON/OFF switch and the input power fuse. The fuse is easily changed as...

Page 11 - DIP SWITCH SETTINGS; for introductory

Pelco Manual C1943M (9/99) 11 SETUP PRELIMINARY DISCUSSION The CM9760-VCRC-P enables automatic control (via macro execution) or manual control(from the CM9760-KBD) of seven predefined VCR functions. Each VCRC-P can control upto 64 VCRs. VCR control is implemented by associating System 9760 GPIs to V...

Page 12 - Figure 10. DIP Switch Functions

12 Pelco Manual C1943M (9/99) Figure 10. DIP Switch Functions NOTE: POSITIONS 9 AND 10ARE NOT USED AND SHOULDBE LEFT IN THE FACTORYDEFAULT “OFF” POSITION.

Page 13 - Access the tab labeled “Type” and select VCR as the input type.; Figure 11. Configuring MGR Camera File for VCRC-P Operation; It is a good idea to

Pelco Manual C1943M (9/99) 13 SOFTWARE SETUP–USING THE MGR PROGRAMTO CONFIGURE VCRC-P OPERATION The VCRC-P unit controls up to 64 VCRs per unit and provides seven basic functions ofVCR control direct from the CM9760 keyboard. These controls include Stop, Pause, Play,Eject, Fast Forward, Rewind, and ...

Page 14 - Figure 12. Configuring the GPI SETUP file for VCRC-P Operation

14 Pelco Manual C1943M (9/99) 7. This brings up the GPI SETUP file dialog box (.GPI file). Refer to Figure 12. 8. Program logical GPI numbers for all the physical numbers that will be used. The physi-cal GPI numbers correspond to a specific VCR control signal on the VCR controller.These GPI numbers ...

Page 15 - Figure 13. Configuring the COMMS file for VCRC-P Operation

Pelco Manual C1943M (9/99) 15 Figure 13. Configuring the COMMS file for VCRC-P Operation 10. Define operator access, save the GPI file, return to the MGR main menu screen and press the tab to bring up the COMMS file (.SCP file). Refer to Figure 13. 11. In the COMMs file assign an equipment number “1...

Page 16 - INSTALLATION; REMOTE OPERATION

16 Pelco Manual C1943M (9/99) INSTALLATION Physical installation of the VCRC-P unit is relatively simple, although various configurationsare possible. DIRECT RACK-MOUNT HOOK-UP Regardless of the location of a VCRC-P unit, it will more than likely be installed in a rack(refer to Figure 14). The VCRC-...

Page 17 - OPERATIONAL OVERVIEW; FUNCTIONAL BLOCK DIAGRAM; Figure 16. VCRC-P Functional Block Diagram

Pelco Manual C1943M (9/99) 17 OPERATIONAL OVERVIEW The basic function of the VCRC-P unit is to act as an interface between the user/operatorof the system and any connected VCRs. Each VCRC-P processes and executes only com-mands with addresses that match the controller address. When a VCRC-P receives...

Page 18 - Control additional VCRs by repeating steps 1 and 2.; Figure 17. CM9760-KBD VCR Control Functions

18 Pelco Manual C1943M (9/99) OPERATING THE CM9760-VCRC-P FROM THE CM9760-KBD Direct control operation of VCRs attached to VCRC-Ps from a CM9760-KBD is relativelystraightforward. Once the system is running and the keyboard is online, direct control of aVCR is as follows: 1. Select an input (camera) ...

Page 19 - SPECIFICATIONS; Electrical; Data Por ts; General; Dimensions; Mechanical; Connectors; PRODUCT WARRANTY AND RETURN INFORMATION

Pelco Manual C1943M (9/99) 19 SPECIFICATIONS Electrical Input Voltage: Auto-ranging 100-240 VAC, 50/60 Hz Power: Consumption: 30 vA Data Por ts Input: RS-422, RJ-45 connectorDIP switch selectable baud rate Output: RS-422, RJ-45 connector.DIP switch selectable baud rate Output: DB-9 connectorFactory ...

Page 20 - REVISION HISTORY; REGULATORY NOTICES; Reorient or relocate the receiving antenna.

20 Pelco Manual C1943M (9/99) Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, System 9760, and Spectra are registered trademarks of Pelco. © Copyright 1999, Pelco. Endura and ExSite are trademarks of Pelco. All rights reserved. REVISION HISTORY Manual # Date Comments C1943M 9/99 Original v...