Pelco C1927M - Manuals - manualsarea.com

Page 2 - CONTENTS; Section

2 Pelco Manual C1927M (5/99) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 5 DESCRIPTION ................................................................................................................... 5 WHAT IS A VIDEO MU...

Page 3 - LIST OF ILLUSTRATIONS; Figure; LIST OF TABLES; Table

Pelco Manual C1927M (5/99) 3 LIST OF ILLUSTRATIONS Figure Page 1 Stand-Alone Multiplexer ..................................................................................... 7 2 Multiplexers with KBD4000 Keyboard ................................................................ 7 3 Multiplexers with...

Page 5 - IMPORTANT SAFEGUARDS AND WARNINGS; Only use replacement parts recommended by Pelco.; DESCRIPTION; WHAT IS A VIDEO MULTIPLEXER?

Pelco Manual C1927M (5/99) 5 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specifically ...

Page 6 - GENEXTM SERIES SIMPLEX MULTIPLEXERS; Video from the cameras can be shown on two monitors: main and spot.; APPLICATIONS

6 Pelco Manual C1927M (5/99) Not only does the number of cameras affect the time gap, but so does the recording speed.The slower the recording speed, the longer the gap. Normal recording speed for full motionis the two-hour mode. But if you slow the recording speed down to record 12 hours, 48hours, ...

Page 7 - Figure 2. Multiplexers with KBD4000 Keyboard; compatible. In Figure 1 cameras are; such as Intercept

Pelco Manual C1927M (5/99) 7 Figure 2. Multiplexers with KBD4000 Keyboard By adding a KBD4000 keyboard to the multiplexer (refer to Figure 2), you can control 1-16multiplexers from up to 25 feet (7.6 m) away with the cable supplied with the keyboard.Greater distances between the multiplexer and keyb...

Page 8 - MODELS; Color Simplex

8 Pelco Manual C1927M (5/99) MODELS Color Simplex MX4009CS 9-channel, color simplex multiplexer, NTSC standard, 120 VAC, 60 Hz(UL, cUL, FCC) MX4009CS-X Same as MX4009CS except PAL standard, 230 VAC, 50 Hz (CE) MX4016CS 16-channel, color simplex multiplexer, NTSC standard, 120 VAC, 60Hz (UL, cUL, FCC...

Page 9 - INSTALLATION; BASIC INSTALLATION; Figure 4. Rack Installation

Pelco Manual C1927M (5/99) 9 INSTALLATION Unpack and inspect all parts carefully. The following parts are supplied: 1 MX4000 Series multiplexer 1 Rack ear kit2 Rack ears 4 4-40 x .375-inch pan head screws 4 10-32 x .750-inch pan head screws 1 Power cord 1 6-foot (1.8 m) data cable with RJ-45 connect...

Page 10 - Proceed to the; CAMERAS; Stand-Alone Multiplexer; - Connect fixed cameras. Moveable cameras may be; Table A. Video Coaxial Cable Requirements; Maximum Distance; Figure 5. Camera Wiring Example; Camera power

10 Pelco Manual C1927M (5/99) 3. Attach the rack ears (C) to the multiplexer. The rack ears are universal and can beused on either side of the unit. Attach the ears with the 4-40 x .375-inch screws (D)that are supplied with the ears. Only the two bottom holes on the rack ears are neededfor mounting....

Page 11 - MONITORS; Main Monitor; Skip this section if; Figure 6. VCR Wiring Example

Pelco Manual C1927M (5/99) 11 MONITORS Main Monitor - The main monitor can show live video of an individual camera or a sequence of individual cameras, the same as the spot monitor. But the main monitor is theonly monitor that can show multi-screen displays (more than one camera displayedsimultaneou...

Page 12 - Figure 7. Pelco Time-Lapse VCR W iring Example

12 Pelco Manual C1927M (5/99) 2. For proper recording, the switching rate of the multiplexer between cameras mustmatch that of the VCR. There are two ways to do this: a. One way is with a head switching pulse from the VCR. This is the most reliableway to synchronize the multiplexer and VCR. The puls...

Page 13 - PELCO’S TIME-LAPSE VCRS; ALARMS; Figure 8. Alarm W iring Example

Pelco Manual C1927M (5/99) 13 PELCO’S TIME-LAPSE VCRS You can connect one of Pelco’s Time-Lapse VCR Models TLR2024, TLR2096, or TLR2168to the multiplexer as follows (refer to Figure 7): 1. Connect BNC video cable between the VCR connectors on the multiplexer and theVIDEO connectors on the VCR. 2. Au...

Page 15 - Figure 10. Front Panel, 16-Channel Color Simplex Multiplexer; MULTIPLEXER WITH MX4000SVR SERVER; Refer to Figure 3 in the; OPERATION

Pelco Manual C1927M (5/99) 15 Figure 9. Front Panel, 9-Channel Color Simplex Multiplexer DISPLAYRECORD Sim DISPLAYRECORD Sim Figure 10. Front Panel, 16-Channel Color Simplex Multiplexer MULTIPLEXER WITH MX4000SVR SERVER Refer to Figure 3 in the Applications section for an overview of a typical insta...

Page 16 - Table B. Front Panel Controls; Button

16 Pelco Manual C1927M (5/99) Table B. Front Panel Controls Button Operation Function DISPLAY/ Press once Toggles main monitor display between record, live inputs, and playback from VCR. RECORD In the RECORD mode, the red LED lights. Press for 3 seconds Displays or exits the record setup menu on the...

Page 17 - Table C. Operation Guide; RESULT

Pelco Manual C1927M (5/99) 17 OPERATION FRONT PANEL COMMAND Call a camera to the main Press any CAMERA button. monitor. Call a camera to the spot Press any CAMERA button twice. monitor. Set main tracking 1. Go to the Advanced System Setup menu. 2. Press the arrow buttons so the cursor highlights SPO...

Page 19 - PROGRAMMING; PASSWORD; Advanced; MENUS; To program the main system parameters:

Pelco Manual C1927M (5/99) 19 PROGRAMMING Programming allows you to configure the multiplexer for the way that you want your systemto operate. The multiplexer automatically selects the most common operating parametersand can be operated without programming it. You should program the multiplexer if y...

Page 20 - Global Setups; Figure 11. Basic System Setup Menu; In any menu you can

20 Pelco Manual C1927M (5/99) 4. When the menu item you desire is highlighted (blinking), do one of the following: • If a menu item has more than one option, press the +/- button to cycle throughthe options to select the one you want. • If a menu item has only one option, press the +/- button to sel...

Page 21 - Figure 12. Advanced System Setup Menu

Pelco Manual C1927M (5/99) 21 NO CHANGE - This is a pass-through selection in case you unintentionally hit the +/-button. This is not an undo button. Alarm Inputs Refer to the Alarms section for an explanation of normally closed and normally open operation. Dwell Rates Sets the sequence dwell rate f...

Page 22 - Sets the format for displaying the date on the main monitor.

22 Pelco Manual C1927M (5/99) Date Format Sets the format for displaying the date on the main monitor. Password Enables or disables password control to access programming menus. Front Panel Control Enables or disables the front panel buttons to operate the multiplexer. In either modeyou can access p...

Page 24 - UNIVERSAL; Figure 13. Basic VCR Settings Menu

24 Pelco Manual C1927M (5/99) Table D. VCR Types NTSC PAL UNIVERSAL UNIVERSAL GYYR TLC1800 ASUTSA TLVCR 251 GYYR 2100 ASUTSA TLVCR 964 GYYR 2100 HD MODE BURLE TC3910X JVC SR-L900U HITACHI VTL30E JVC SR-L901U HITACHI VT-L1000E JVC SR-9070U HITACHI VT-L2000E JVC BR-S925U JVC BR9060E MITSUBISHI HS7424U...

Page 25 - Figure 14. Custom VCR Setup Menu; To program the advanced VCR parameters:; Record Speeds

Pelco Manual C1927M (5/99) 25 Figure 14. Custom VCR Setup Menu CUSTOM VCR SETUP (DISPLAY/RECORD BUTTON) To program the advanced VCR parameters: 1. Press the DISPLAY/RECORD button for approximately three seconds. The RecordSetup menu appears. 2. Make sure the VCR Type in the Record Setup menu is set ...

Page 26 - Video Termination; Refer to the; Coaxitron; OFF - Use when your system has fixed cameras only.; Figure 15. Basic Camera Menu

26 Pelco Manual C1927M (5/99) CAMERA SETUP (CAMERA BUTTONS) To program a camera input: 1. Press the desired CAMERA button for approximately three seconds. Type thepassword, if requested. The Camera menu appears. A video insert appears that showswhat the camera is viewing. This is useful to make sure...

Page 27 - Activity Detection; When you have completed all the changes you want to make, go to EXIT.; ACTIVITY MASK SETUP; To program an activity mask for a camera:; Figure 16. Activity Dectection Mask

Pelco Manual C1927M (5/99) 27 Activity Detection A camera can be set to respond or not to respond to motion. If enabled, select SETDETECTION MASK to define what part of the camera’s viewing field will be monitoredfor motion. 5. To program another camera, press the button for that camera. Repeat step...

Page 29 - HELP MENU; Figure 18. Help Menu; Figure 17. Camera Sequence Menu; MULTIPLE CAMERA DISPLAY SETUP

Pelco Manual C1927M (5/99) 29 HELP MENU The Help menu is accessed from any other menu. 1. Use the up and down arrow buttons in any menu to highlight HELP. 2. Press the +/- button. The Help menu appears. Figure 18. Help Menu GROUP QUAD (2x2) 1 04 2 04 3 04 4 04 NINE (3x3) 0404 DISP/REC BUTTON SETTING...

Page 30 - All active cameras

30 Pelco Manual C1927M (5/99) PROGRAMMING THE 4-CAMERA DISPLAYS ( BUTTON) You can program four groups of four cameras each. Each of the four groups can be programmed to include any four cameras. is not available in RECORD mode. To program the four-camera displays: 1. Press the button to call up a fo...

Page 31 - PROGRAMMING MENU DEFAULTS; Table E. Programming Menu Defaults; Menu

Pelco Manual C1927M (5/99) 31 PROGRAMMING MENU DEFAULTS Table E. Programming Menu Defaults Menu Item Default System Setup Time Display On Title Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA)3 Hr (PAL/CCIR) Alarm Record Speed 2/6/8 Hr (NTSC/EIA)3 Hr (PAL/CCIR) Main Monitor Display High Resolution...

Page 32 - TROUBLESHOOTING

32 Pelco Manual C1927M (5/99) TROUBLESHOOTING If you have difficulty operating your system, run through the following checklist to see if youcan solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server ...

Page 33 - RESET; SPECIFICATIONS; VIDEO

Pelco Manual C1927M (5/99) 33 RESET To reset the multiplexer: 1. Unplug the power cord. 2. Press and hold the VIEW button on the front panel of the multiplexer while you plugthe power cord into an electrical outlet. When the Initialization Menu appears, releasethe VIEW button. The monitor will indic...

Page 34 - REVISION HISTORY; Date; Preliminary version released for beta evaluation.; WARRANTY AND RETURN INFORMATION; REGULATORY NOTICES

34 Pelco Manual C1927M (5/99) REVISION HISTORY Manual # Date Comments C1927M 3/99 Preliminary version released for beta evaluation. 5/99 Original version. ® Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. WARRANTYPelco will repair or replace...