Pelco C1666M-A (4/06) 3 - Manuals

Page 3 - Important Safety Instructions

C1666M-A (4/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the ma...

Page 4 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

4 C1666M-A (4/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesire...

Page 5 - Description

C1666M-A (4/06) 5 Description The TW3001AR is a single-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable. The adaptive technology in the TW3001AR automatically adjusts the low , medium and high frequency components of the video signal allowing for the best ...

Page 6 - PARTS OF THE RECEIVER; Rack Power Connector:

6 C1666M-A (4/06) PARTS OF THE RECEIVER Figure 1. TW3001AR Parts Rubber Feet (4): For placing unit on a flat surface, such as a desk or shelf. Status LED: Lights red when there is no UTP video being received. Lights green when there is UTP video being received. Flashes amber when Coaxitron pan/tilt/...

Page 7 - Installation; MOUNTING; USING A RACK

C1666M-A (4/06) 7 Installation Make sure all parts are present for the unit. 1 Universal power supply (Part #PS04-1502-0512G) 1 Wall clip 1 2-pin power connector 1 2-pin UTP connector MOUNTING The TW3001AR receiver is 3 rack units high and can be mounted into a fi ber rack, onto a wall using a fiber...

Page 8 - USING A WALL CLIP

8 C1666M-A (4/06) USING A WALL CLIP To attach the TW3001AR receiver to a wall using the supplied wall clip, refer to Figure 2 and do the following: 1. Attach the wall clip to a wall using two screws (not supplied). 2. Slide the receiver into the clip until the two holes on the bottom of the receiver...

Page 9 - SETTING THE DIP SWITCHES

C1666M-A (4/06) 9 SETTING THE DIP SWITCHES You can override the adaptive technology by manually adjusting switches 1-4 on the DIP Switch. The factory default switch positions are shown in Figure 3. Switches 1-4 are set to AUTO and Switch 5 is set to High Mode. Figure 3. Default Switch Positions If y...

Page 10 - APPLICATIONS; Cable Type

10 C1666M-A (4/06) APPLICATIONS You can connect the TW3001AR active receiver to transmitters, such as the TW3001P passive trans-ceiver and the TW3001AT active transmitter, and to Pelco UTP cameras, such as the CC3710/CC3610 Series. Although you can connect these products using an unshielded twisted ...

Page 17 - Specifications; ELECTRICAL

C1666M-A (4/06) 17 Specifications ELECTRICAL Input Voltage 12 VDC or 24 VAC, 50-60Hz Power Consumption 2.5 watts Wire Type Unshielded Twisted Pair (24 AWG maximum) Wire Category Cat3 or better DC Loop Resistance 52 ohms per 1,000 feet Differential Capacitance 19pF/ft max Transient Immunity 300 W pea...

Page 19 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic ...