Pelco C1570M-E (4/07) - Manuals

6 C1570M-E (4/07) Regulatory Notices REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that...

C1570M-E (4/07) 7 Description The CM9700MDD-EVS matrix digital decoder uses the latest Endura ™ technology to transmit video from Endura products to CM9700 Series matrix switchers (using 9.03.012 software, or higher). Adding the CM9700MDD-EVS to a matrix system allows a security operator to use the ...

8 C1570M-E (4/07) FRONT VIEW Figure 1 illustrates the components on the front of the CM9700MDD-EVS. Refer to Front Panel Indicators on page 40 for a description of each indicator. Figure 1. CM9700MDD-EVS Front View REAR VIEW Figure 2 illustrates the components on the rear of the CM9700MDD-EVS. Refer...

C1570M-E (4/07) 9 SAMPLE APPLICATION IMPORTANT NOTE. PLEASE READ The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the...

10 C1570M-E (4/07) Installation HARDWARE INSTALLATION OVERVIEW The following steps provide an overview of how to install the CM9700MDD-EVS: 1. Install all components of the matrix switching system. Refer to the matrix system documentation for instructions. 2. Install one or more CM9700MDD-EVS units,...

C1570M-E (4/07) 11 PRODUCT SERIAL NUMBER LABEL PLACEMENT Product serial number labels help Pelco’s Product Support identify your system and its factory configuration in the event that the CM9700MDD-EVS or its components require service. A label citing your product’s serial number is attached to the ...

12 C1570M-E (4/07) MOUNTING Use one of the following installation methods for the CM9700MDD-EVS: • Place the CM9700MDD-EVS on a flat surface, such as a shelf or desktop • Mount the CM9700MDD-EVS to a wall using the optional WM5001-4U wall mount kit • Install the CM9700MDD-EVS in the optional RK5000P...

C1570M-E (4/07) 13 WALL MOUNT INSTALLATION The CM9700MDD-EVS can be mounted to a wall using the optional WM5001-4U wall mount system. You can mount up to four CM9700MDD-EVS units, in any combination, in a fully expanded WM5001-4U (one WM5001-4U with up to three WM5001-4UEXP expansion units). To moun...

14 C1570M-E (4/07) RACK MOUNT INSTALLATION Up to 12 CM9700MDD-EVS units can be mounted in the optional RK5000PS-5U rack mount kit. Each unit plugs directly into a power connector in the rack and is powered by the rack. NOTE: The RK5000PS-5U only supplies power. It does not provide a dock for any oth...

C1570M-E (4/07) 15 PELCO BADGE ORIENTATION The Pelco badge on the front panel of the CM9700MDD-EVS can be rotated in quarter turns. If you install the unit on a flat surface, the Pelco badge will be turned the wrong way. To rotate the Pelco badge: 1. Use the Pelco badge rotation sticker that came wi...

16 C1570M-E (4/07) BASIC HARDWARE CONNECTIONS CM9700-CC1 CONNECTION Use the 16-pin terminal block (included with the CM9700MDD-EVS) for the RS-422 serial connection (Pelco P protocol) between the CM9700MDD-EVS and the CM9700-CC1. Figure 12 shows how to wire the terminal block and connect it to the C...

C1570M-E (4/07) 17 Figure 13. Connecting the CM9700MDD-EVS to the CM9700-CC1 MATRIX BAY CONNECTION 1. Connect a coaxial cable to the video out connector on the CM9700MDD-EVS (refer to the CM9700MDD-EVS rear panel illustration in Figure 2 on page 8 and to the matrix bay connection drawings shown on t...

C1570M-E (4/07) 21 AUDIO OUTPUT CONNECTION The CM9700MDD-EVS supports one audio output, which allows you to control a speaker or other audio equipment at the monitored location. NOTE: When using multiple CM9700MDD-EVS units, an additional audio routing solution may be required. Figure 17. Audio Outp...

22 C1570M-E (4/07) NETWORK CONNECTION NOTE: Consult your network administrator before installing the CM9700MDD-EVS to avoid possible network conflicts. Use the network port on the front panel and a 100BaseT network Cat5e (or better) cable with RJ-45 connectors to connect the CM9700MDD-EVS to your sy...

C1570M-E (4/07) 23 POWER CONNECTION The CM9700MDD-EVS offers a single four-pin power connector. The RK5000PS-5U rack mount kit and the NET5301PS attach to the four-pin connector. When using a different power supply, attach power to the enclosed four-pin to two-pin adapter and attach the adapter to t...

24 C1570M-E (4/07) Connect power to the CM9700MDD-EVS. The Pelco badge (blue) and the status light (green) on the front panel should glow. Figure 19. Connecting the Power FOUR-PIN OR ADAPTER

C1570M-E (4/07) 25 Software Configuration Once the hardware installation and all device connections are completed, you will need to complete the following software configuration tasks: • Use the CM9700-MGR software to add the CM9700MDD-EVS and Endura cameras to the matrix system configuration. Instr...

26 C1570M-E (4/07) ADD THE CM9700MDD-EVS AND ENDURA CAMERAS TO THE 9700 MATRIX CONFIGURATION To add a CM9700MDD-EVS to a 9700 matrix system configuration, you need to complete the following tasks: 1. Add the CM9700MDD-EVS to the matrix system configuration. Refer to Add the CM9700MDD-EVS to the Matr...

28 C1570M-E (4/07) CONFIGURE THE CM9700MDD-EVS SETTINGS When you click a CM9700MDD-EVS unit in the tree view portion of the CM9700-MGR main window, the CM9700MDD-EVS unit’s properties open in the properties box. Use these property fields to configure each CM9700MDD-EVS unit. Figure 25. Configuring C...

C1570M-E (4/07) 29 ADD ENDURA CAMERAS TO THE MATRIX SYSTEM CONFIGURATION 1. Click Wizards > Add Device Wizard. The Add Device wizard opens. 2. Specify Camera in the Select Device Type drop-down box, and then click EnduraCam in the Select Model drop-down box. Figure 26. Adding an Endura Camera 3. ...

30 C1570M-E (4/07) Figure 28. Device Identification Page 6. Specify the device name(s) and logical number range by completing the following fields: Name: Type a base name for the device. If you want a space between the name and the logical number, use the spacebar to enter a space after the name. Yo...

C1570M-E (4/07) 31 CONFIGURE A CM9700 SOFT ALARM TO REPRESENT AN ENDURA ALARM 1. Use the Endura WS5000 application to configure alarms in the Endura system. Be sure to assign each alarm a unique logical number. These can be contact alarms or motion alarms. Refer to the WS5000 Operation manual and th...

32 C1570M-E (4/07) MACRO CONFIGURATION To configure a CM9700 macro to activate a script in the Endura system, complete the following steps: 1. In the Endura system configure a script to complete the desired task. Note that you must use a unique logical number as the script name, which you will use i...

34 C1570M-E (4/07) NETWORK VIDEO RECORDER MANAGEMENT You can use the matrix system and the CM9700MDD-EVS as an NVR (network video recorder) management tool. Sample NVR management scenario: This sample system includes the following components: • Cameras connected to the matrix switcher • NVRs connect...

36 C1570M-E (4/07) CONFIGURE A CM9700 MACRO TO SWITCH VIDEO TO A BACKUP NVR 1. Use the CM9700-MGR software to add a macro, and then click Edit Steps to open the Macro Editor window. Refer to the Macros section in the CM9700-MGR Software Guide for detailed instructions. Figure 39. Adding a Macro for ...

C1570M-E (4/07) 37 ASSOCIATE A MACRO WITH A SOFT ALARM 1. Use the CM9700-MGR Add Soft Alarms Wizard to add a soft alarm for each NVR. 2. (Optional) Give each alarm a recognizable name. 3. Click a soft alarm, and then select a macro in the Macro drop-down box. Figure 41. Associate a Macro with a Soft...

C1570M-E (4/07) 39 3. Use the Endura WS5000 application to transfer the XML file to the CM9700MDD-EVS through the Endura network, as described in the following steps: a. Click the Devices tab in the WS5000 Setup window. b. Navigate to the CM9700MDD-EVS unit. A NOTE ABOUT CM9700MDD-EVS DEVICE NAMES I...

40 C1570M-E (4/07) Operation FRONT PANEL INDICATORS Figure 46. CM9700MDD-EVS Front Panel Pelco badge (power indicator) The Pelco badge glows blue when the unit has power. Unit status indicator Unit status is indicated by one of the following three colors: Green The unit is functioning normally. Ambe...

C1570M-E (4/07) 41 VIEWING VIDEO If you have not already done so, install the CM9760-KBD keyboard, connect it to the matrix system, and then complete the basic setup process. Refer to the CM9760-KBD/CM9760-KBR Installation/Operation manual for instructions; this manual is provided in the matrix syst...

42 C1570M-E (4/07) 5. To switch the video mode (from live to recorded, or vice versa), press the MORE icon to view DVR Menu 2, and then press the Switch Mode icon. Figure 48. DVR Menu 2 6. To access the remaining DVR icons, which appear on DVR Menu 3, press the MORE icon. Figure 49. DVR Menu 3 SWITC...

C1570M-E (4/07) 43 VIEWING AND CONTROLLING VIDEO NOTE: In the following procedures the “Select Play” or “Select Pause” step can be accomplished either by moving the joystick or by pressing the keyboard icon. Identify the CM9700MDD-EVS Unit If your system includes more than one CM9700MDD-EVS unit, an...

44 C1570M-E (4/07) Seek (Search for a Specific Time) Live Video 1. While viewing live video, press the Seek icon. The keyboard LCD displays the date field. 2. Enter the date (MMDDYYYY), and then press the Seek icon again. The keyboard LCD displays the time field. 3. Enter the time (HHMMSS), and then...

C1570M-E (4/07) 45 Using Digital Zoom (Recorded Video Only) During playback of recorded video, you can use the digital zoom feature to enlarge a portion of the video image. When the digital zoom feature is enabled, you will see a picture-in-picture frame on the monitor. The picture-in-picture frame ...

46 C1570M-E (4/07) Controlling Recorded Video with the Joystick Many of the joystick movements described below operate in both momentary and latching modes. These modes are defined as follows: • Momentary mode: The operation is activated until you release the joystick. Moving the joystick a small di...

C1570M-E (4/07) 47 Current Mode = Play: • To the right a little: video plays at 2x (momentary). • To the right a little more: video plays at 4x (momentary). • To the right all the way: video plays at 2x (latching). • To the right all the way again: video plays at 4x (latching). • To the right all th...

48 C1570M-E (4/07) CONFIGURING THE OFFSET+ AND OFFSET - FUNCTIONS TO SWITCH CAMERAS The Offset+ and Offset - functions allow you to configure an offset value, which allows an easy way to switch cameras. To configure the Offset+ and Offset - functions, complete the following steps: 1. Assign the Offs...

C1570M-E (4/07) 49 Figure 53. Assigning an Alternate Camera 3. Specify the Endura logical camera number as the alternate camera. For the example described above, you would specify logical camera number 5001. 4. Click OK to close the Alternate Cameras dialog box, and then save the configuration chang...

50 C1570M-E (4/07) Troubleshooting If the following instructions fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 or 1-559-292-1981 for assistance. Access the properties window for the CM9700MDD-EVS unit on the WS5050 Endura workstation (refer to the WS5000 operation manua...

C1570M-E (4/07) 51 Specifications MODEL CM9700MDD-EVS Matrix digital decoder (NET5301R optimized for use with matrix) that converts digital video streams from Endura products into analog video to be viewed and controlled on a Pelco CM9700 Series matrix switcher. SUPPLIED ACCESSORIES Mating Connector...

52 C1570M-E (4/07) POWER Power Consumption 12 W, 41 BTU/H Power Input 12 VDC +10%/-15%24 VAC +10%/-15% Power Connectors 4-pin For RK5000PS-5U or NET5301PS 4-pin to 2-pin adapter For user-supplied power supply ENVIRONMENTAL Ambient Temperature 70° to 74°F (21° to 23°C) Operating Temperature Range 32°...

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material orworkmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW30...