Pelco C1498M-B - Manuals - manualsarea.com

Page 2 - CONTENTS; LIST OF ILLUSTRATIONS

2 Pelco Manual C1498M-B (7/99) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................ 3 DESCRIPTION ................................................................................................................... 3 MODELS ............

Page 3 - MODELS; INSTALLATION

Pelco Manual C1498M-B (7/99) 3 IMPORTANT SAFEGUARDS AND WARNINGS Observe the following warnings before installing and using this product. 1. Installation and servicing should only be done by qualified service personnel andconform to all local codes. 2. Unless the unit is specifically marked as a NEM...

Page 4 - Make; Table A. Switch Settings for SW1; For Coaxitron

4 Pelco Manual C1498M-B (7/99) 2. Set the switches on the bottom of the dome drive. Refer to Table A for the settings forSW1, and Table B and Table C for SW2. 3. Install the dome drive in the back box. Line up the green tab and red tab on the domedrive with the green label and red label on the back ...

Page 5 - Table C. Switch Settings for SW2 – D-Type Control

Pelco Manual C1498M-B (7/99) 5 Receiver Address Switch Setting SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OF...

Page 9 - OPERATION; The dome will stop

Pelco Manual C1498M-B (7/99) 9 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 231 ON ON ON OFF OFF ON ON ON 232 OFF OFF OFF ON OFF ON ON ON 233 ON OFF OFF ON ...

Page 10 - PAN AND TILT FUNCTIONS; Fixed-Speed Controllers –; AUTO FLIP; Zoom Telephoto –; PRESET FUNCTIONS; For American

10 Pelco Manual C1498M-B (7/99) PAN AND TILT FUNCTIONS Use your controller’s joystick to control pan and tilt operation. • Fixed-Speed Controllers – Pan and tilt operation is at a fixed speed; the controller determines the speed. • Variable-Speed Controllers – Depending on the joystick’s position, s...

Page 12 - Compensation

12 Pelco Manual C1498M-B (7/99) CM9750 1. Turn the KEY SWITCH to the ON position. 2. Press the PROG key. PROGRAM appears on the LCD screen. 3. Press the PRES key. The PRESET prompt appears. 4. Enter 95 and press the ENTER key. The main menu appears. 5. Turn the KEY SWITCH to the OFF position. CM9760...

Page 14 - SHUTTER SPEED

14 Pelco Manual C1498M-B (7/99) 6. Move the joystick up or down to position the cursor beside one of the choices. Pressthe Iris Open button. MODE – The cursor moves to one of two choices: Auto or Off. In the Auto mode, the iris is automatically adjusted to produce a constant video output as determin...

Page 15 - AUTO WHITE BALANCE –; LINE SYNCHRONIZATION

Pelco Manual C1498M-B (7/99) 15 To change the mode: 1. On the main menu, move the joystick up or down to position the cursor (>) beside Camera. 2. Press the Iris Open button to enter the Camera submenu. 3. Move the joystick up or down to position the cursor beside Next. 4. Press the Iris Open but...

Page 17 - MANUAL LIMIT STOPS; PARK TIME MINUTES; Programming; NOTE

Pelco Manual C1498M-B (7/99) 17 LIMIT STOPS The two types of limit stop are manual and scan. When manual limit stops are set, a manual(joystick) pan operation stops when a limit is reached. When scan limit stops are set, thedome reverses direction during random, frame, and auto scanning when a limit...

Page 18 - TROUBLESHOOTING; Pendant Models –

18 Pelco Manual C1498M-B (7/99) 3. Move the joystick up or down to position the cursor beside Scan Speed deg/s. 4. Press the Iris Open button. The cursor moves to the right beside the current number ofdegrees. 5. Move the joystick up or down to toggle through the number of degrees (1-40) until youre...

Page 19 - BACK BOX ELECTRONIC ASSEMBLY REMOVAL; SPECIFICATIONS; MECHANICAL

Pelco Manual C1498M-B (7/99) 19 8. If the red power LED is lit, turn off power. a. Open the door to the interconnect circuit board and check that all connectors arefully seated. b. Make sure the wiring is correct between the unit and controller. c. Close the door. Check the switch settings on the do...

Page 20 - REVISION HISTORY; WARRANTY AND RETURN INFORMATION; REGULATORY NOTICES

20 Pelco Manual C1498M-B (7/99) REVISION HISTORY Manual # Date Comments C1498M 2/99 Original version. 3/99 Removed reference to line synchronization. Added material on auto iris. Added FCC notice. C1498M-A 7/99 Revised the preset tilt speed from 100 to 200 degrees/second. Added model number and spec...