Pelco C1458M-J - Manuals - manualsarea.com

Page 2 - Contents

2 C1458M-J (9/08) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - Important Safety Instructions

C1458M-J (9/08) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources, suc...

Page 4 - Description; MODELS

4 C1458M-J (9/08) Description DF5 Series domes are discreet surveillance domes that are designed for indoor or outdoor use. Models include pendant and in-ceiling versions. In-ceiling models have plenum-rated back boxes and can be installed in hard ceilings or standard 2 x 2 ft (6 x 61 cm) suspended ...

Page 5 - Installation; PARTS LIST; PENDANT MODELS; Back Box

C1458M-J (9/08) 5 Installation PARTS LIST The DF5 shipping carton contains two boxes. Inspect each box to make sure all parts are present. IN-CEILING MODELS Back Box Qty Description 1 Back box with tilt table assembly installed (includes camera and lens if specified with order) 1 Parts bag 1 Safety ...

Page 6 - BACK BOX

6 C1458M-J (9/08) BACK BOX IN-CEILING MODELS, HARD CEILINGS 1. Locate the center point of the mounting location. Drill a hole in the ceiling using a 3/32-inch drill. Insert the compass tool into the hole. Use a pencil and the compass tool to draw a circle on the ceiling. Carefully cut out the circle...

Page 7 - PENDANT MODELS, PENDANT MOUNT

C1458M-J (9/08) 7 IN-CEILING MODELS, SUSPENDED CEILING 1. Remove the ceiling tile from the ceiling. Insert the compass tool (supplied) into the center of the tile. (If necessary, use a 3/32-inch bit to drill a hole.) Draw a circle on the tile using the compass tool and a pencil. Carefully cut out th...

Page 8 - PENDANT MODELS, SURFACE MOUNT

8 C1458M-J (9/08) PENDANT MODELS, SURFACE MOUNT 1. If you have an outdoor model, remove the sun shield. 2. Remove the black tilt table assembly inside of the back box by removing the nuts and washers that hold the three legs to the back box. 3. Remove the top mount by removing the three screws and l...

Page 9 - CAMERA AND LENS

C1458M-J (9/08) 9 CAMERA AND LENS If the camera and lens are already installed, begin with step 2. 1. If applicable, extend the lens to the maximum length before installing the camera in the back box. Attach the camera to the tilt table with the 1/4-20 screw, flat washer, and lock washer (supplied)....

Page 10 - LOWER DOME

10 C1458M-J (9/08) LOWER DOME IN-CEILING MODELS 1. Snap the clip on the end of the trim ring leash into the hole on the lip of the back box. 2. Line up the snaps on the trim ring with the mounting screws on the back box. Snap the trim ring into the plastic snap washers on the mounting screws. Figure...

Page 11 - Maintenance; EXTERIOR SURFACE; SMOKED OR CLEAR; RECOMMENDED CLEANING PROCEDURE

C1458M-J (9/08) 11 Maintenance Clean the acrylic dome as needed. Be careful not to scratch the surfaces of the dome. EXTERIOR SURFACE Clean the dome’s exterior surface with a nonabrasive cleaning cloth and agent that is safe for acrylic plastic. Either liquid or spray cleaner/wax suitable for fine f...

Page 12 - Specifications; ELECTRICAL

12 C1458M-J (9/08) Specifications ELECTRICAL Input Voltage 24 VAC (outdoor models only) Input Power 58 VA (for heater) MECHANICAL Construction Back Box Aluminum Mounting Bracket Steel Lower Dome Acrylic Trim Ring Indoor Eggshell white molded plastic, UL94V0 Outdoor Plastic GENERAL Environment Indoor...

Page 13 - Maximum Distance; Wire Gauge

C1458M-J (9/08) 13 Appendix *Cable requirements: 75-ohm impedanceAll-copper center conductorAll-copper braided shield with 95% braid coverage Table B shows are the recommended maximum distances for 24 VAC applications and are calculated with a 10 percent voltage drop. (Ten percent is generally the m...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW30...