Pelco 300 - Manuals - manualsarea.com

Page 2 - CONTENTS; Section

[ 2 ] Pelco Manual C2408M-F (4/03) CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; instructions unless you are qualified to do so.; DESCRIPTION; The 300 Series Camclosure; INSTALLATION; The following parts are supplied:

Pelco Manual C2408M-F (4/03) [ 3 ] IMPORTANT SAFEGUARDS AND WARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near ...

Page 4 - Prepare Wall or Ceiling; Mounting directly to wall or ceiling

[ 4 ] Pelco Manual C2408M-F (4/03) 1 Prepare Wall or Ceiling Prepare the wall or ceiling according to one of the options shown below. Mounting directly to wall or ceiling Mounting to a 4S electrical boxwith 404 plaster ring Mounting to ICS300-COND conduit adapter(not supplied) Mounting to a two-gang...

Page 5 - Attach Base; Release the base locking ring for access to the mounting holes.; Connect Video and Power; disconnect the heater wiring.; TIP

Pelco Manual C2408M-F (4/03) [ 5 ] NOTCH 3 Attach Base Release the base locking ring for access to the mounting holes. Mounting hardware is not supplied if you attach the base directlyto a wall or ceiling. To attach the base to an adapter plate or conduit adapter, two6-32 x 1.25-inch tamper-resistan...

Page 6 - Ver tical Phase; Reverse the 24 VAC connections on one camera. If; Adjust Camera

[ 6 ] Pelco Manual C2408M-F (4/03) ADJUSTMENTS (Color Camera Only) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes,however, adjustments may be necessary. 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vert...

Page 7 - Auto Iris Level Adjustment; VARIFOCAL LENS; Switch Settings for Varifocal Lens; To enable automatic exposure; CAUTION; Do not change the shutter; Backlight compensation

Pelco Manual C2408M-F (4/03) [ 7 ] Auto Iris Level Adjustment If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the iris level settingto increase or decrease brightness. VARIFOCAL LENS FIXED LENS Switch Settings for Varifocal Lens The high resolution camera wi...

Page 9 - C A U T I O N

Pelco Manual C2408M-F (4/03) [ 9 ] Focus Adjustment for Fixed Focal Length Lenswith Auto Iris To adjust the focus: 1. Loosen the locking screw on the bottom of the lens. To loosen the screw, it may be necessary to remove theheater board. Refer to the figure below and the accom-panying steps. 2. Move...

Page 10 - Electrical

[ 10 ] Pelco Manual C2408M-F (4/03) Regulatory Notices FCC Class A (monochrome, EIA cameras only) NOTE: This equipment has been tested and found to comply with the limits of a Class A digital device,pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection agai...

Page 11 - PRODUCT WARRANTY AND RETURN INFORMATION

Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, and Camclosure are registered trademarks of Pelco. End ura and ExSite are trademarks of Pelco. ©Copyright 2003, Pelco. All rights reserved. PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any mercha...