Pelco 2 C1306M-B (10/06) - Manuals

Page 3 - Important Safety Instructions; RISK OF ELECTRIC SHOCK.

C1306M-B (10/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. To reduce the risk of ignition of hazard...

Page 4 - Getting Started; METHODS OF INSTALLATION

4 C1306M-B (10/06) Getting Started Thank you for purchasing Pelco’s ExSite ™ EHXM Series explosionproof system. This manual includes instructions for installing all the components of the system. Once the system installation is complete, refer to the operation/programming manual for instructions on h...

Page 5 - Install the Power Module

C1306M-B (10/06) 5 Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (140 lb/63.5 kg). NOTE: If required, install the optional TXB translator, fiber module, o...

Page 6 - CONNECT WIRING; Configuration of Wire Harness

6 C1306M-B (10/06) CONNECT WIRING Refer to the following information to connect the wires and cables as required. NOTES: • Relay 3 is allocated specifically for an external washer (not supplied by Pelco). • All relays are specified for 32 VDC, 0.5 A. • Wiring/cable for UTP and fiber optic are not pr...

Page 7 - DIP SWITCH SETTINGS; PROTOCOL SETTINGS; Switch Settings for SW3; Switch Number

C1306M-B (10/06) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. NOTE: No DIP switch settings are required for Coaxitron control. Figure 3 shows the default se...

Page 12 - Install the Camera Module

12 C1306M-B (10/06) Install the Camera Module To install the camera module, do the following: 1. Refer to Figure 4. Loosen the set screw at the back of the camera enclosure with the provided 1.5 mm Allen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanner wrench to loosen the back of the ...

Page 14 - Models with a wiper:

14 C1306M-B (10/06) 4. Models with a wiper: Refer to Figure 8 and do the following to install the arm of the wiper: a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same orientation as shown in Figure 8. b. Install the wiper...

Page 15 - Install the Enclosure and Set Pan Position

C1306M-B (10/06) 15 Install the Enclosure and Set Pan Position 1. Check for proper seating of the power module seal. Make sure the seal is fully seated in the groove on the top of the power module. Figure 9. Factory-Installed Power Module Seal 2. Refer to Figure 10 and attach the enclosure unit to t...

Page 16 - Set the Tilt Angle of the Camera Module

16 C1306M-B (10/06) Set the Tilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nut and a 21 mm open end wrench on the tilt shaft (refer to Figure 11). Figure 11. Set the Tilt Position 2. Hold the tilt shaft in position with the 21 mm wrench, and then tur...

Page 18 - Maintenance; CAMERA MODULE REPLACEMENT

18 C1306M-B (10/06) Maintenance CAMERA MODULE REPLACEMENT To replace the camera module, do the following: 1. Remove the back cap of the camera enclosure. Refer to Figure 13 and do the following: a. Loosen the set screw with a 1.5 mm Allen wrench. b. Use the supplied spanner wrench to loosen the back...

Page 21 - Specifications; ELECTRICAL

C1306M-B (10/06) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input Voltage Range ±10% Power Consumption Maximum 60 W (120 VA) per system Heater and Defroster Microprocessor controlled Electrical Connections 6-foot wire harness with connections for power, video, data control, ala...

Page 23 - PRODUCT WARRANTY AND RETURN INFORMATION

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disp...