Oregon Scientific BAR608HGA - Manuals

Page 2 - CONTENTS

EN 1 CONTENTS Contents ................................................................... 1 Introduction .............................................................. 2 About Oregon Scientific .......................................... 2 Product Overview ..............................................

Page 3 - INTRODUCTION; Thank you for selecting the Oregon Scientific; Wireless; ABOUT OREGON SCIENTIFIC

EN 2 INTRODUCTION Thank you for selecting the Oregon Scientific TM Wireless Weather Station (BAR608HGA). This device bundlesprecise time keeping, weather forecast, barometric trendwith altitude adjustment, and indoor and outdoortemperature and humidity monitoring features into asingle tool you can u...

Page 4 - PRODUCT OVERVIEW; FRONT VIEW

EN 3 PRODUCT OVERVIEW FRONT VIEW 1. SNOOZE / LIGHT button 2. Weather Forecast & Barometric Trend Area 3. Outdoor Temperature & Humidity Area 4. Indoor Temperature & Humidity Area 5. Clock / Alarm Area 6 Moon Phase 7. and : increase or decrease setting / activate or deactivate Atomic Cloc...

Page 5 - BACK VIEW; Wall mount; GETTING STARTED

EN 4 BACK VIEW 1. Wall mount 2. Battery compartment 3. Table stand REMOTE SENSOR (THGR122N) GETTING STARTED 1 2 3 BAR608HGA lab test R2 1/17/04, 4:39 PM 4

Page 6 - RESET

EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1. Wall mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment(Battery compartment cover not shown) 1 2 1 2 3 4 BAR608HGA lab test R2 1/17/04, 4:39 PM 5

Page 7 - BATTERIES

EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. TABLE STAND OR WALL MOUNT Use the stand on the back of the product, or mount it ona wall with a nail. GETTING STARTED BATTERIES Batteries are not supplie...

Page 9 - SEARCH FOR SENSOR; CLOCK; DATA TRANSMISSION

EN 8 SEARCH FOR SENSOR To search for a sensor, press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. S i g n a l s f r o m h o u s e h o l d d e v i c e s s u c h a s doorbells, electronic garage doors, and home s...

Page 10 - ALARMS

EN 9 TURN ATOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clocksignals. Press and hold DOWN for 2 seconds. Then,m a n u a l l y s e t t h e c l o c k f o l l o w i n g t h e " S e t C l o c k "instructions (below). SET CLOCK You only need to do this if you have disabled th...

Page 11 - BAROMETER; BAROMETRIC TREND; WEATHER FORECAST

EN 10 If no button is pressed, the Alarm will automaticallysilence after 2 minutes. It will then sound again after8 minutes. BAROMETER This product tracks barometric pressure changes overthe past 24 hours to provide the weather forecast( 13) and a trend line showing the direction of barometric chang...

Page 12 - TEMPERATURE AND HUMIDITY; SELECT TEMPERATURE UNIT; MOON PHASE

EN 11 NOTE TEMPERATURE AND HUMIDITY T h i s p r o d u c t c a n d i s p l a y c u r r e n t , m i n i m u m , a n dmaximum temperatures and humidity percentageinformation collected by the remote sensors and main(indoor) unit. Outdoor data is collected and displayed every 40seconds. Indoor data is co...

Page 13 - SAFETY AND CARE; NOTE; TROUBLESHOOTING

EN 12 When you press RESET , all settings will return to default value, and you will lose all stored information. SAFETY AND CARE Clean the product with a slightly damp cloth and alcohol-free, mild detergent. Avoid dropping the product orplacing it in a high-traffic location. WARNINGS This product i...

Page 14 - SPECIFICATIONS; MAIN UNIT DIMENSIONS

EN 13 SPECIFICATIONS MAIN UNIT DIMENSIONS L x W x H 142 x 63 x 158 mm(5.5 x 2.5 x 6.2 inches) Weight 366 g (12.96 ounces)with battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm(3.6 x 2.4 x .79 inches) Weight 63 grams (2.22 ounces)without battery TEMPERATURE Unit ° C or ° F Indoor Range -5 ° ...

Page 16 - FCC STATEMENT

EN 15 FCC STATEMENT This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received,i n c l u d i n g i n t e r f e r e n c e t h a t m a y c a u s e u...

Page 17 - DECLARATION OF CONFORMITY; We

EN 16 DECLARATION OF CONFORMITY The information below is not to be used as contact forsupport or sales. Please call our customer service number(listed on our website at www.oregonscientific.com, oron the warranty card for this product) for all inquiriesinstead. We Name: Oregon Scientific, Inc. Addre...