Oregon Scientific BAR608HGA - Manual

EN 4 BACK VIEW 1. Wall mount 2. Battery compartment 3. Table stand REMOTE SENSOR (THGR122N) GETTING STARTED 1 2 3 BAR608HGA lab test R2 1/17/04, 4:39 PM 4

EN 5 REMOTE SENSOR (THGR122NX) 1. LCD display 2. LED Status indicator 1. Wall mount hole 2. RESET 3. Channel number (1 - 3) 4. Battery compartment(Battery compartment cover not shown) 1 2 1 2 3 4 BAR608HGA lab test R2 1/17/04, 4:39 PM 5

EN 6 CHANGE SETTINGS 1. Press and hold MODE for 2 seconds to enter setting mode. 2. Press UP or DOWN to change settings. 3. Press MODE to confirm. TABLE STAND OR WALL MOUNT Use the stand on the back of the product, or mount it ona wall with a nail. GETTING STARTED BATTERIES Batteries are not supplie...

EN 8 SEARCH FOR SENSOR To search for a sensor, press and hold MEM and CHANNEL for 2 seconds. If the sensor is still not found, check the batteries, obstructions, and remote unit location. S i g n a l s f r o m h o u s e h o l d d e v i c e s s u c h a s doorbells, electronic garage doors, and home s...

EN 9 TURN ATOMIC CLOCK ON/OFF Perform this step if you cannot receive Atomic Clocksignals. Press and hold DOWN for 2 seconds. Then,m a n u a l l y s e t t h e c l o c k f o l l o w i n g t h e " S e t C l o c k "instructions (below). SET CLOCK You only need to do this if you have disabled th...

EN 10 If no button is pressed, the Alarm will automaticallysilence after 2 minutes. It will then sound again after8 minutes. BAROMETER This product tracks barometric pressure changes overthe past 24 hours to provide the weather forecast( 13) and a trend line showing the direction of barometric chang...

EN 11 NOTE TEMPERATURE AND HUMIDITY T h i s p r o d u c t c a n d i s p l a y c u r r e n t , m i n i m u m , a n dmaximum temperatures and humidity percentageinformation collected by the remote sensors and main(indoor) unit. Outdoor data is collected and displayed every 40seconds. Indoor data is co...

EN 12 When you press RESET , all settings will return to default value, and you will lose all stored information. SAFETY AND CARE Clean the product with a slightly damp cloth and alcohol-free, mild detergent. Avoid dropping the product orplacing it in a high-traffic location. WARNINGS This product i...

EN 13 SPECIFICATIONS MAIN UNIT DIMENSIONS L x W x H 142 x 63 x 158 mm(5.5 x 2.5 x 6.2 inches) Weight 366 g (12.96 ounces)with battery REMOTE SENSOR DIMENSIONS L x W x H 92 x 60 x 20 mm(3.6 x 2.4 x .79 inches) Weight 63 grams (2.22 ounces)without battery TEMPERATURE Unit ° C or ° F Indoor Range -5 ° ...

EN 15 FCC STATEMENT This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received,i n c l u d i n g i n t e r f e r e n c e t h a t m a y c a u s e u...

EN 16 DECLARATION OF CONFORMITY The information below is not to be used as contact forsupport or sales. Please call our customer service number(listed on our website at www.oregonscientific.com, oron the warranty card for this product) for all inquiriesinstead. We Name: Oregon Scientific, Inc. Addre...