Nortel NN46200-301 - Manuals

Nortel NN46200-301 – Manual in PDF format online.

Manuals:

Manual

Manual Nortel NN46200-301

Summary

Page 2 - Restricted rights legend

Document status: Standard Document version: 03.01 Document date: 27 August 2007 Copyright © 2007, Nortel NetworksAll Rights Reserved. Sourced in Canada and the United States of America The information in this document is subject to change without notice. The statements, configurations, technicaldata...

Page 3 - Contents; New in this release

3 Contents New in this release 5 Features 5 Other changes 5 Preface 7 Command line interfaces 7 NNCLI command modes 7 Accessing the NNCLI 9 Returning to the CLI 10 Text conventions 10 Hard-copy technical manuals 11 How to get help 12 Power supply installation 13 Navigation 13 Power supplies 13 Remov...

Page 5 - Features

5 New in this release See the following sections for details about what’s new in Nortel EthernetRouting Switch 8300 Installation — MAC Addresses (NN46200-600) forRelease 4.0: • "Features" (page 5) • "Other changes" (page 5) Features There are no new feature-related changes for this d...

Page 7 - Preface; Command line interfaces; NNCLI command modes

7 Preface The Nortel Ethernet Routing Switch 8300 is a flexible and multifunctionalLayer 2/Layer 3 switch that supports diverse network architectures andprotocols. The Ethernet Routing Switch 8300 provides security and controlfeatures such as Extensible Authentication Protocol over LAN (EAPoL),Simpl...

Page 9 - Prompt; Accessing the NNCLI; and save the

Command line interfaces 9 Table 1NNCLI command modes Commandmode Prompt Modename Command/modeto enter or exit mode User EXEC ERS-8300:5> Exec Default modewhen NNCLI is started logout to exit PrivilegedEXEC ERS-8300:5# privExec enable to enter from User EXEC mode disable to exit to User EXEC mode ...

Page 10 - nortel; Returning to the CLI; To switch from the NNCLI to the CLI, enter the following commands:; no boot flags nncli; You must reboot the switch for this change to take effect.; Text conventions; This guide uses the following text conventions:; ping; show ip alerts; show ip routes

10 Preface Password: nortel ERS-8310:5# configure terminal ERS-8310:5(config)# Returning to the CLI The config.cfg file for the CLI and the config.cfg file for the NNCLI are notcompatible. If you decide to change the CLI mode to NNCLI, or the reverse,you must use the config.cfg file for the selected...

Page 11 - show ip interfaces; show at; Hard-copy technical manuals

Hard-copy technical manuals 11 brackets ([ ]) Indicate optional elements in syntax descriptions.Do not type the brackets when entering thecommand. Example: If the command syntax is show ip interfaces [-alerts] , you can entereither show ip interfaces or show ip interfaces -alerts . ellipsis points (...

Page 12 - URL to download a; How to get help; web page and click Technical Support.

12 Preface You can print the technical manuals and release notes free, directly fromthe Internet. Use Adobe Acrobat Reader to open the manuals and releasenotes, search for the sections you need, and print them on most standardprinters. Go to Adobe Systems at the www.adobe.com URL to download a free ...

Page 13 - Power supply installation; Navigation

13 Power supply installation This guide contains information about installing power supplies. Navigation • "Power supplies" (page 13) • "Removing and installing a power filler panel" (page 17) • "Installing the AC power supply" (page 18) • "Removing the AC power supply...

Page 14 - shows an Ethernet Routing

14 Power supply installation Figure 18301AC power supply Figure 2 "8302AC power supply" (page 14) shows an Ethernet Routing Switch 8302AC power supply. The nominal input voltage range for the 8302AC power supply is 100-120VAC and 200-240VAC, however, the output power is limited to 850 Wmaxim...

Page 15 - State; the number of modules installed in the chassis; Number of power supplies

Power supplies 15 The following table describes the power supply LED on the AC power supply. Table 2Power supply LEDs State Meaning Off Power supply not operational. Contact your Nortel TechnicalSolutions Center. On (green) Power supply is ok. The Ethernet Routing Switch 8300 chassis ships with no i...

Page 16 - Note the following information:; Redundancy

16 Power supply installation Note the following information: • If a power supply fails when you have a redundant power supplyinstalled, the Ethernet Routing Switch 8300 continues to operate withno interruption of service. The chassis will continue to supply the samemodule and PoE output power with t...

Page 17 - Removing and installing a power filler panel; To remove a filler panel:; Step; Step; Place the power filler panel in the empty power supply bay.

Removing and installing a power filler panel 17 Removing and installing a power filler panel A power filler panel maintains the proper cooling airflow in the EthernetRouting Switch 8300 Series chassis. If you remove a power supply from theEthernet Routing Switch 8300 Series chassis without replacing...

Page 18 - —End—; Installing the AC power supply; Install the AC power supply to provide AC power for components.; DANGER; To install an AC power supply:; Remove the filler panel from the power bay if necessary.

18 Power supply installation —End— Installing the AC power supply Install the AC power supply to provide AC power for components. Do not install the 8301AC power supply and the 8302AC power supplywithin the same chassis. This configuration is not supported. When you first install a 8000 Series chass...

Page 19 - CAUTION; For instructions, see

Installing the AC power supply 19 CAUTION Save the power filler panel in case you need to operatethe 8300 Series chassis with a power supply removed. 2 If you are replacing a failed power supply, then remove the failedsupply. For instructions, see "Removing the AC power supply" (page 20) . 3...

Page 20 - Turn on the power switch.; Removing the AC power supply

20 Power supply installation 7 Turn on the power switch. The power supply LED on the power supply should light green. —End— Removing the AC power supply DANGER Due to high-energy hazards of working with components of greaterthan 240 VA, only qualified service personnel are permitted toinstall and re...

Page 21 - To remove an AC power supply:; Loosen the two retaining screws on the power supply.

Removing the AC power supply 21 You should replace a failed power supply as soon as possible to restorehigh-availability operation. CAUTION To maintain proper cooling, never operate the Ethernet RoutingSwitch 8300 Series chassis with an empty power supply bay. Ifyou are replacing a failed power supp...

Page 22 - Pull the power supply out of the chassis.

22 Power supply installation 4 Lift the extractor lever to disconnect the power supply from thebackplane connector. 5 Pull the power supply out of the chassis. 6 Install a new power supply (see "Installing the AC power supply" (page 18) ) or install a power filler panel (see "Removing an...

Page 23 - AC Input Power Ratings; DC Output Power Ratings

23 AppendixElectrical specifications for the ACpower supply This appendix lists the electrical specifications for the Ethernet RoutingSwitch 8301AC power supply. Refer to your chassis installation manual forsystem power specifications. The following table list the power specifications for the Ethern...

Page 28 - Installation — AC Power Supply

Nortel Ethernet Routing Switch 8300 Installation — AC Power Supply Copyright © 2007, Nortel NetworksAll Rights Reserved. Publication: NN46200-301 Document status: Standard Document version: 03.01 Document date: 27 August 2007 Sourced in Canada and the United States of America To provide feedback or ...