Nortel LKG-Nortel ELO GS8MP - Manuals

iii Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit Power Cord Safety Please read the following safety information carefully before installing this switch: Warning: Installation and removal of the unit must be carried out by qualified personnel only. • The unit must be connected to an earthe...

iv Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following: Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch: AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être...

vii Environmental Statement The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved through the following means: • Adherence to national legislation and regulations on environmental production standards. • C...

ix Contents Chapter 1: Introduction 1-1 Overview 1-1 Switch Architecture 1-2 Power-over-Ethernet Capability 1-2 Network Management Options 1-2 Description of Hardware 1-3 10/100/1000BASE-T Ports 1-3 SFP Slot 1-3 Port and Power Status LEDs 1-3 Power Supply Socket 1-4 Features and Benefits 1-5 Connect...

x Contents Chapter 4: Making Network Connections 4-1 Connecting Network Devices 4-1 Twisted-Pair Devices 4-1 Power-over-Ethernet Connections 4-1 Cabling Guidelines 4-2 Connecting to PCs, Servers, Hubs and Switches 4-2 Network Wiring Connections 4-3 Fiber Optic SFP Devices 4-4 Connectivity Rules 4-6 ...

xi Tables Table 1-1 Port Status LEDs 1-4 Table 1-2 Power Status LED 1-4 Table 4-1 Maximum 1000BASE-T Gigabit Ethernet Cable Length 4-6 Table 4-2 Maximum 1000BASE-SX Fiber Optic Cable Length 4-6 Table 4-3 Maximum 1000BASE-LX Fiber Optic Cable Length 4-6 Table 4-4 Maximum 1000BASE-LH Fiber Optic Cable...

xii Figures Figure 1-1 Front Panel 1-1 Figure 1-2 Rear Panel 1-1 Figure 1-3 Port and Power LEDs 1-3 Figure 1-4 Power Supply Socket 1-4 Figure 2-1 PoE Connections 2-2 Figure 2-2 Collapsed Backbone 2-3 Figure 2-3 Meeting Room 2-3 Figure 2-4 Making VLAN Connections 2-4 Figure 3-1 RJ-45 Connections 3-2 ...

1-1 Chapter 1: Introduction Overview The LNGS8MP is an intelligent Layer 2 switch with eight 10/100/1000BASE-T ports, one of which is a Gigabit combination port * that is shared with an SFP transceiver slot. The switch’s eight 10/100/1000 Mbps ports support the IEEE 802.3af Power-over-Ethernet (PoE)...

Introduction 1-2 1 Switch Architecture The switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of multiple packets at low latency on all ports. The switch also features full-duplex capability on all ports, which effectively doubles the bandwidth...

Description of Hardware 1-3 1 Description of Hardware 10/100/1000BASE-T Ports The switch contains eight RJ-45 ports that operate at 10 Mbps or 100 Mbps, half or full duplex, or at 1000 Mbps, full duplex. Because all ports on the switch support automatic MDI/MDI-X operation, you can use straight-thro...

Introduction 1-4 1 Power Supply Socket The power socket is located on the rear panel of the switch. The standard power socket is for the AC power cord. Figure 1-4 Power Supply Socket Table 1-1 Port Status LEDs LED Condition Status Fast Ethernet Ports (Ports 1-8)Link/Act (Link/Activity) On/Flashing G...

Features and Benefits 1-5 1 Features and Benefits Connectivity • 8 10/100/1000 Mbps ports for easy Gigabit Ethernet integration and for protection of your investment in legacy LAN equipment. • All RJ-45 ports support IEEE 802.3af standard Power-over-Ethernet• Auto-negotiation enables each RJ-45 port...

2-1 Chapter 2: Network Planning Introduction to Switching A network switch allows simultaneous transmission of multiple packets via non-crossbar switching. This means that it can partition a network more efficiently than bridges or routers. The switch has, therefore, been recognized as one of the mo...

Network Planning 2-2 2 Application Examples The switch is not only designed to segment your network, but also to provide a wide range of options in setting up network connections. Some typical applications are described below. Supplying PoE The switch is an excellent choice for supplying power to co...

Application Examples 2-3 2 access points are receiving PoE power from the switch. Figure 2-2 Collapsed Backbone Meeting Room With eight 1000 Mbps parallel bridging ports (i.e., eight distinct collision domains), this switch can function as an efficient bridged node that is ideal for a meeting room e...

Network Planning 2-4 2 Making VLAN Connections The switch supports VLANs that can be used to organize any group of network nodes into separate broadcast domains. VLANs confine broadcast traffic to the originating group, and can eliminate broadcast storms in large networks. This provides a more secur...

Application Notes 2-5 2 Application Notes 1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstation, server or another switch). When the switch is connected to a hub, both devices must operate in half-duplex mode. 2. For network applications t...

3-1 Chapter 3: Installing the Switch Selecting a Site switch units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to follow the guidelines below when choosing a location. • The site should: • be at the center of all the devices you want to link and near a power out...

Installing the Switch 3-2 3 Figure 3-1 RJ-45 Connections Equipment Checklist After unpacking the switch unit, check the contents to be sure you have received all the components. Then, before beginning the installation, be sure you have all other necessary installation equipment. Package Contents • L...

Mounting 3-3 3 Rack Mounting Before rack mounting the switch, pay particular attention to the following factors: • Temperature: Since the temperature within a rack assembly may be higher than the ambient room temperature, check that the rack-environment temperature is within the specified operating ...

Installing the Switch 3-4 3 2. Mount the device in the rack, using four rack-mounting screws (not provided). Figure 3-3 Installing the Switch in a Rack 3. If installing a single switch only, turn to “Connecting to a Power Source” at the end of this chapter. 4. If installing multiple switches, mount ...

Installing an Optional SFP Transceiver 3-5 3 2. Set the device on a flat surface near an AC power source, making sure there are at least two inches of space on all sides for proper air flow. 3. If installing a single switch only, go to “Connecting to a Power Source” at the end of this chapter. 4. If...

Installing the Switch 3-6 3 Connecting to a Power Source To connect a device to a power source: 1. Insert the power cable plug directly into the socket located at the back of the device. Figure 3-6 Power Socket 2. Plug the other end of the cable into a grounded, three-pin, AC power source. Note: For...

4-1 Chapter 4: Making Network Connections Connecting Network Devices The switch units are designed to interconnect multiple segments (or collision domains). It can be connected to network cards in PCs and servers, as well as to hubs, switches or routers. It may also be connected to devices using opt...

Making Network Connections 4-2 4 Cabling Guidelines The RJ-45 ports on the switch support automatic MDI/MDI-X pinout configuration, so you can use standard straight-through twisted-pair cables to connect to any other network device (PCs, servers, switches, routers, or hubs). See Appendix B: for furt...

Twisted-Pair Devices 4-3 4 Network Wiring Connections Today, the punch-down block is an integral part of many of the newer equipment racks. It is actually part of the patch panel. Instructions for making connections in the wiring closet with this type of equipment follows. 1. Attach one end of a pat...

Making Network Connections 4-4 4 Fiber Optic SFP Devices An optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-LH) can be used for a backbone connection between switches, or for connecting to a high-speed server. Each single-mode fiber port requires 9/125 micron single-mode fiber...

Making Network Connections 4-6 4 Connectivity Rules When adding hubs (repeaters) to your network, please follow the connectivity rules listed in the manuals for these products. However, note that because switches break up the path for connected devices into separate collision domains, you should not...

Connectivity Rules 4-7 4 100 Mbps Fast Ethernet Collision Domain 10 Mbps Ethernet Collision Domain Table 4-5 Maximum Fast Ethernet Cable Length Type Cable Type Maximum Cable Length Connector 100BASE-TX Category 5 or better 100-ohm UTP or STP 100 m (328 ft) RJ-45 Table 4-6 Maximum Ethernet Cable Leng...

Making Network Connections 4-8 4 Cable Labeling and Connection Records When planning a network installation, it is essential to label the opposing ends of cables and to record where each cable is connected. Doing so will enable you to easily locate inter-connected devices, isolate faults and change ...

A-1 Appendix A: Troubleshooting Diagnosing Switch Indicators Power and Cooling Problems If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or internal power supply. However, if the unit powers off after running for a w...

Troubleshooting A-2 A Installation Verify that all system components have been properly installed. If one or more components appear to be malfunctioning (such as the power cord or network cabling), test them in an alternate environment where you are sure that all the other components are functioning...

B-1 Appendix B: Cables Twisted-Pair Cable and Pin Assignments For 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For 1000BASE-T connections the twisted-pair cable must have four pairs of wires. Each wire pair is identified by two different colors. For example, on...

Cables B-2 B Table B-1 10/100BASE-TX MDI-X and MDI Port Pinouts Straight-Through Wiring If the twisted-pair cable is to join two ports and only one of the ports has an internal crossover (MDI-X), the two pairs of wires must be straight-through. (When auto-negotiation is enabled for any RJ-45 port on...

Twisted-Pair Cable and Pin Assignments B-3 B any RJ-45 port on the switch, you can use either straight-through or crossover cable to connect to any device type.) You must connect all four wire pairs as shown in the following diagram to support Gigabit Ethernet connections. Figure B-3 Crossover Wirin...

Cables B-4 B Cable Testing for Existing Category 5 Cable Installed Category 5 cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-End Crosstalk (FEXT). This cable testing information is specified in the ANSI/TIA/EIA-TSB-67 standard. Additionally, cables must also pass test pa...

C-1 Appendix C: Specifications Physical Characteristics Ports 8 10/100/1000BASE-T, with auto-negotiation1 SFP transceiver slot. Network Interface Ports 1-8: RJ-45 connector, auto MDI/X 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better)100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or bett...

Specifications C-2 C AC Input 100 to 240 V, 50-60 Hz, 1.5 A Power-over-Ethernet Input voltage: 48 V DC Maximum output power 70 W: 15.4 W for any four ports simultaneously port 1 can provide 25 W Maximum output current per port: 350 mA DC port 1 can reach: 565 mA DCOutput Voltage: 44 - 57 V DCMaximum...

Standards C-3 C Standards IEEE 802.3-2005 Ethernet, Fast Ethernet, Gigabit Ethernet IEEE 802.3af Power-over-EthernetIEEE 802.1D Spanning Tree ProtocolIEEE D802.1Q Virtual LANIEEE 802.1X, Port-Based Network Access Control, 2001 ISO/IEC 8802-3 Compliances CE MarkEmissions FCC Class A Immunity EN 61000...

Glossary-1 Glossary 10BASE-T IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable. 100BASE-TX IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable. 1000BASE-LH Specification for long-haul Gigabit Ethernet over...

Index-1 Numerics 10 Mbps connectivity rules 4-7100 Mbps connectivity rules 4-71000 Mbps connectivity rules 4-61000BASE-LH fiber cable lengths 4-61000BASE-LX fiber cable lengths 4-61000BASE-SX fiber cable lengths 4-61000BASE-T pin assignments B-3ports 1-3 100BASE-TX cable lengths 4-7ports 1-3 10BASE-...