Nortel 2600 - Manuals - manualsarea.com

Page 3 - Installing Hardware Options for the Contivity VPN Switch; USA requirements only; EC Declaration of Conformity

3 Installing Hardware Options for the Contivity VPN Switch USA requirements only Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rul...

Page 4 - Bureau of Standards, Metrology and Inspection (BSMI) statement; Canada requirements only

4 302283-E Rev 00 Japan/Nippon requirements only Voluntary Control Council for Interference (VCCI) statement (Class A) Voluntary Control Council for Interference (VCCI) statement (Class B Contivity 1600 and 2600) Taiwan requirements Bureau of Standards, Metrology and Inspection (BSMI) statement Cana...

Page 5 - Canada CS-03 rules and regulations

5 Installing Hardware Options for the Contivity VPN Switch Canadian Department of Communications Radio Interference Regulations This digital apparatus (Contivity 1600 and Contivity 2600) does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Inter...

Page 6 - FCC Part 68 compliance statement

6 302283-E Rev 00 Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'énergie électrique, des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante da...

Page 7 - Nortel Networks Inc. software license agreement

7 Installing Hardware Options for the Contivity VPN Switch 2. Your telephone company may make changes to its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. The telephone company will notify you in advance of such changes to give you an op...

Page 8 - Use of software in the European Community.

8 302283-E Rev 00 remedy Nortel Networks will at its discretion provide a suitable fix, patch, or workaround for the problem that may be included in a future Software release. Nortel Networks further warrants to Licensee that the media on which the Software is provided will be free from defects in m...

Page 9 - Contents; Preface

9 Installing Hardware Options for the Contivity VPN Switch Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 10 - Index

10 302283-E Rev 00 Installing Contivity 2500/2000/4000 LAN/WAN option cards . . . . . . . . . . . . . . . . . . . . 48 Installing Contivity 2500/2000/4000 DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Replacing a Contivity 4000 power supply . . . . . . . . . . . . . . . ...

Page 11 - Figures

11 Installing Hardware Options for the Contivity VPN Switch Figures Figure 1 Removing the Contivity 4600 front bezel . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 2 Contivity 4600 front components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 3 Sample Contivit...

Page 13 - Improper handling of internal; Do

13 Installing Hardware Options for the Contivity VPN Switch Preface This document describes how Nortel Networks* trained service personnel can install or replace hardware components for models 4600, 4500, 4000, 2600, 2500, 2000, 1600, and 600 of the Contivity* products. The options include: • Instal...

Page 14 - Related publications; Contivity VPN Switch Release Notes; Text conventions; This guide uses the following text conventions:; ping; bold Courier text

14 Preface 302283-E Rev 00 This guide refers to the Contivity 4600, 4500, 4000, 2600, 2000, 1600, and 600 as the switch. It assumes that you are familiar with Web browsers and their general operation. Related publications The following list shows the associated documentation that you will need to co...

Page 15 - italic text

Preface 15 Installing Hardware Options for the Contivity VPN Switch braces ({}) Indicate required elements in syntax descriptions where there is more than one option. You must choose only one of the options. Do not type the braces when entering the command.Example: If the command syntax is show ip {...

Page 16 - Acronyms; show ip

16 Preface 302283-E Rev 00 Acronyms This guide uses the following acronyms: vertical line ( | ) Separates choices for command keywords and arguments. Enter only one of the choices. Do not type the vertical line when entering the command.Example: If the command syntax is show ip {alerts|routes} , you...

Page 17 - Hard-copy technical manuals; Technical Solutions Center

Preface 17 Installing Hardware Options for the Contivity VPN Switch Hard-copy technical manuals You can print selected technical manuals and release notes free, directly from the Internet. Go to the www.nortelnetworks.com/documentation URL. Find the product for which you need documentation. Then loc...

Page 18 - URL and click

18 Preface 302283-E Rev 00 An Express Routing Code (ERC) is available for many Nortel Networks products and services. When you use an ERC, your call is routed to a technical support person who specializes in supporting that product or service. To locate an ERC for your product or service, go to the ...

Page 20 - Chapter 1 Contivity 4600 Option Installation; Figure 1; Removing the Contivity 4600 front bezel

20 Chapter 1 Contivity 4600 Option Installation 302283-E Rev 00 Figure 1 shows you how to remove the front bezel from the Contivity 4600. You do not need to turn off the switch to remove the front bezel when installing a power supply or hard disk drive. Figure 1 Removing the Contivity 4600 front bez...

Page 21 - Figure 2; Contivity 4600 front components

Chapter 1 Contivity 4600 Option Installation 21 Installing Hardware Options for the Contivity VPN Switch Figure 2 shows the Contivity 4600 front components. Figure 2 Contivity 4600 front components Disk drives Floppy drive Power supplies Alert/Fail Boot/Ready CS460006A

Page 22 - Contivity 4600 system board layout; This section shows the Contivity 4600 system board.; Figure 3; Sample Contivity 4600 system board; Only Nortel Networks trained service personnel should; DIMM

22 Chapter 1 Contivity 4600 Option Installation 302283-E Rev 00 Contivity 4600 system board layout This section shows the Contivity 4600 system board. Figure 3 shows a sample Contivity 4600 system board, including the Dual Inline Memory Modules (DIMMs) and peripheral component interconnect (PCI) slo...

Page 23 - Remove the filler panel screw and pull out the slot filler panel.; Figure 4; Secure the option card in the tray with the slot filler panel screw.

Chapter 1 Contivity 4600 Option Installation 23 Installing Hardware Options for the Contivity VPN Switch Installing Contivity 4600 LAN/WAN and hardware accelerator cards This section describes how you install option cards in the switch option card slide-out tray. The following procedure is for Norte...

Page 24 - Plug in both power cords to the power source and turn on the switch.; Installing Contivity 4600 DIMMs; Figure 6

24 Chapter 1 Contivity 4600 Option Installation 302283-E Rev 00 7 Plug in both power cords to the power source and turn on the switch. Installing Contivity 4600 DIMMs Figure 6 shows you how to unlock a DIMM in the Contivity 4600, and remove or install a DIMM. Install a DIMM in the next available slo...

Page 25 - Figure 5; Replacing a Contivity 4600 power supply; To remove the power supply:

Chapter 1 Contivity 4600 Option Installation 25 Installing Hardware Options for the Contivity VPN Switch Figure 5 Installing Contivity 4600 DIMMs 7 Pull up the locking levers on both sides of the next available DIMM, and snap the DIMM into its socket. 8 Replace the support bracket by tightening the ...

Page 26 - Removing a Contivity 4600 power supply; Secure the power supply screws tightly with a screwdriver.

26 Chapter 1 Contivity 4600 Option Installation 302283-E Rev 00 Figure 6 Removing a Contivity 4600 power supply 3 Grab the handle and pull the power supply firmly, until the device disengages. Be careful of the sharp sheet-metal edges. 4 Insert the new power supply. Make sure it seats firmly in its ...

Page 27 - Replacing a Contivity 4600 hard disk drive; Figure 7

Chapter 1 Contivity 4600 Option Installation 27 Installing Hardware Options for the Contivity VPN Switch Replacing a Contivity 4600 hard disk drive Figure 7 shows you how to replace Contivity 4600 hard disk drives for the switch. To replace a hard disk drive, you must do the following: Software Firs...

Page 28 - Removing a Contivity 4600 hard disk drive; Replace the front bezel.

28 Chapter 1 Contivity 4600 Option Installation 302283-E Rev 00 Figure 7 Removing a Contivity 4600 hard disk drive 3 Insert the replacement hard drive fully, and lock it by turning the key clockwise. Make sure the hard disk drive LED shows the proper drive number. 4 Replace the front bezel. If you n...

Page 29 - Software

Chapter 1 Contivity 4600 Option Installation 29 Installing Hardware Options for the Contivity VPN Switch Software Enable the switch by following these steps: 1 Use your Web browser to navigate to the switch, and go to the Admin ! File System display. 2 Click on the drive and click the Enable button.

Page 31 - Removing the Contivity 4500 front bezel; Wear an antistatic band when handling electronic

31 Installing Hardware Options for the Contivity VPN Switch Chapter 2Contivity 4500 Option Installation This section describes how to install or replace hardware components for the Contivity 4500. Opening the Contivity 4500 To replace power supplies, replace hard disk drives, or access the Contivity...

Page 32 - Chapter 2 Contivity 4500 Option Installation; Slide your fingers between the front bezel and the switch.; Figure 8

32 Chapter 2 Contivity 4500 Option Installation 302283-E Rev 00 1 Insert a flat-head screwdriver into the slots on the lower left and right sides of the chassis, and pry the bezel forward. 2 Slide your fingers between the front bezel and the switch. 3 Pull the bezel forward firmly, separating the ba...

Page 33 - Remove the Contivity 4500 front bezel to:; Figure 9; Contivity 4500 front components

Chapter 2 Contivity 4500 Option Installation 33 Installing Hardware Options for the Contivity VPN Switch Remove the Contivity 4500 front bezel to: • Replace a power supply. • Replace a hard disk drive. • Insert the recovery diskette. Figure 9 shows the Contivity 4500 front components. Figure 9 Conti...

Page 34 - Contivity 4500 system board layout

34 Chapter 2 Contivity 4500 Option Installation 302283-E Rev 00 Contivity 4500 system board layout This section describes installing option cards onto the system board. Warning: Only Nortel Networks trained service personnel should change existing hardware configurations. Improper handling of intern...

Page 35 - shows the Contivity 4500 system board, in particular the DIMMs and; Sample Contivity 4500 system board

Chapter 2 Contivity 4500 Option Installation 35 Installing Hardware Options for the Contivity VPN Switch Figure 10 shows the Contivity 4500 system board, in particular the DIMMs and option card slots. Figure 10 Sample Contivity 4500 system board DIMMslots CS450013A PCIslots 4321 6 5 4 3 2 1

Page 37 - shows you how to install LAN, WAN, or hardware accelerator option; you must populate the slots from; Installing 4500 LAN/WAN and hardware accelerator option cards

Chapter 2 Contivity 4500 Option Installation 37 Installing Hardware Options for the Contivity VPN Switch Figure 11 shows you how to install LAN, WAN, or hardware accelerator option cards into the Contivity 4500. You can use the 6 slots for any mix of LAN and WAN or hardware accelerator cards; howeve...

Page 38 - shows you how to unlock a Dual Inline Memory Module (DIMM) in; Installing Contivity 4500 DIMMs

38 Chapter 2 Contivity 4500 Option Installation 302283-E Rev 00 Installing Contivity 4500 DIMMs Figure 12 shows you how to unlock a Dual Inline Memory Module (DIMM) in the Contivity 4500, and remove or install a DIMM. Install a DIMM in the next available slot (for example, if the DIMM #1 slot is pop...

Page 39 - To install a DIMM into the Contivity 4500, follow these steps:

Chapter 2 Contivity 4500 Option Installation 39 Installing Hardware Options for the Contivity VPN Switch To install a DIMM into the Contivity 4500, follow these steps: 1 Turn off the switch. 2 Remove the power cords. 3 Unscrew the slide-out tray at the back of the unit and pull it out using the thum...

Page 40 - Replacing a Contivity 4500 power supply; shows you how to replace a hot-swappable power supply for the; Removing a Contivity 4500 power supply

40 Chapter 2 Contivity 4500 Option Installation 302283-E Rev 00 Replacing a Contivity 4500 power supply Figure 13 shows you how to replace a hot-swappable power supply for the Contivity 4500. Figure 13 Removing a Contivity 4500 power supply To remove the power supply: 1 Remove the front bezel as sho...

Page 41 - Replacing a Contivity 4500 hard disk drive

Chapter 2 Contivity 4500 Option Installation 41 Installing Hardware Options for the Contivity VPN Switch 4 Insert the new power supply. Make sure the power supply seats firmly in its socket and is locked in. Be sure the green power LED on the front of the power supply is on. 5 Secure the power suppl...

Page 42 - Installing the Contivity 4600

42 Chapter 2 Contivity 4500 Option Installation 302283-E Rev 00 Figure 14 Removing a Contivity 4500 hard disk drive 3 Insert the replacement hard drive fully, and lock it by turning the key clockwise. Make sure the hard disk drive LED shows the proper drive number. 4 Replace the front bezel. 5 Reloa...

Page 43 - shows you

43 Installing Hardware Options for the Contivity VPN Switch Chapter 3Contivity 2500/2000/4000 Option Installation This section describes how to install or replace hardware components for the Contivity 2500, 2000, and 4000. Opening the Contivity 2500/2000/4000 To install LAN or WAN cards, install har...

Page 46 - two

46 Chapter 3 Contivity 2500/2000/4000 Option Installation 302283-E Rev 00 Contivity 2500/2000/4000 system board layout Figure 17 shows the Contivity 2500/200 system board, in particular the DIMMs, option card slots, and the CPU cooling fan. The Contivity 4000 system board is similar, but has two CPU...

Page 48 - shows you how to install LAN or WAN option cards into a Contivity

48 Chapter 3 Contivity 2500/2000/4000 Option Installation 302283-E Rev 00 Installing Contivity 2500/2000/4000 LAN/WAN option cards Figure 19 shows you how to install LAN or WAN option cards into a Contivity 2500/2000/4000. You can use Slots 1 to 3 for any mix of LAN and WAN cards. Note that Slot 4 i...

Page 50 - Replacing a Contivity 4000 power supply; shows you how to replace a power supply for a Contivity 4000.

50 Chapter 3 Contivity 2500/2000/4000 Option Installation 302283-E Rev 00 Figure 20 Installing Contivity 2500/2000/4000 DIMMs Replacing a Contivity 4000 power supply Figure 21 shows you how to replace a power supply for a Contivity 4000. A l i g n m e n tk e y s L o c k i n g l e v e r T o r e m o v...

Page 51 - Press the button down to turn off the power supply.

Chapter 3 Contivity 2500/2000/4000 Option Installation 51 Installing Hardware Options for the Contivity VPN Switch Figure 21 Removing a Contivity 4000 power supply To remove a Contivity 4000 power supply, remove the switch’s front bezel, then follow these steps: 1 Press the button down to turn off t...

Page 52 - Replacing a Contivity 4000 disk drive

52 Chapter 3 Contivity 2500/2000/4000 Option Installation 302283-E Rev 00 Replacing a Contivity 4000 disk drive To replace a Contivity 4000 disk drive, you must do the following: Software First save any data that has not yet been saved to the hard disk from the disk cache: 1 Use your Web browser to ...

Page 53 - Pull the handle to remove the hard disk drive.

Chapter 3 Contivity 2500/2000/4000 Option Installation 53 Installing Hardware Options for the Contivity VPN Switch Figure 22 Removing a Contivity 4000 hard disk drive 2 Pull the handle to remove the hard disk drive. 3 Insert the replacement hard drive fully, and lock it by turning the key clockwise....

Page 55 - Memory option

Chapter 3 Contivity 2500/2000/4000 Option Installation 55 Installing Hardware Options for the Contivity VPN Switch To replace or change a DIMM, follow these steps. 1 Turn off the switch. 2 Remove the power cord. 3 Remove the front bezel as shown in Figure 15 . 4 Remove the top cover as shown in Figu...

Page 58 - Chapter 4 Contivity 2600 Option Installation; do not; need to turn off the switch if you are; only; removing the front bezel.; Removing the Contivity 2600 front bezel; Removing the front bezel on the Contivity 2600 system activates

58 Chapter 4 Contivity 2600 Option Installation 302283-E Rev 00 Removing the Contivity 2600 front bezel You must remove the bezel to insert the recovery diskette. Note that you do not need to turn off the switch if you are only removing the front bezel. Figure 24 shows you how to remove the front be...

Page 59 - To remove the front bezel, you need a Phillips screwdriver.; Removing the Contivity 2600 top cover; shows you how to remove the top

Chapter 4 Contivity 2600 Option Installation 59 Installing Hardware Options for the Contivity VPN Switch The first few times you remove the front bezel it will be rather difficult to remove. This is because the ball studs and socket clips are new. After a few times, removal is easier. To remove the ...

Page 60 - Contivity 2600 system board layout; shows the Contivity 2600’s system board, in particular the DIMMs,

60 Chapter 4 Contivity 2600 Option Installation 302283-E Rev 00 Figure 25 Removing the Contivity 2600 top cover ➨ Slide the top cover forward approximately 1/4 inch, then lift the lid 2 to 3 inches and move it away from the chassis. Contivity 2600 system board layout Figure 26 shows the Contivity 26...

Page 61 - same

Chapter 4 Contivity 2600 Option Installation 61 Installing Hardware Options for the Contivity VPN Switch Figure 26 The Contivity 2600 system board Warning: Beware of danger if battery is incorrectly replaced. Replace with the same or an equivalent battery only, as recommended by the manufacturer’s i...

Page 62 - Installing LAN/WAN or hardware accelerator cards; Power off the switch.

62 Chapter 4 Contivity 2600 Option Installation 302283-E Rev 00 Installing LAN/WAN and hardware accelerator option cards Figure 27 shows you how to install LAN, WAN, or hardware accelerator option cards into the switch. You can use Slots 1 to 4 for any mix of LAN and WAN cards. Figure 27 Installing ...

Page 64 - shows you how to unlock a Dual Inline Memory Module (DIMM) and; Installing Contivity 2600 DIMMs

64 Chapter 4 Contivity 2600 Option Installation 302283-E Rev 00 Installing Contivity 2600 DIMMs Figure 28 shows you how to unlock a Dual Inline Memory Module (DIMM) and remove or install the DIMM in the next available slot (for example, if the DIMM #1 slot is populated, add the next DIMM to the DIMM...

Page 68 - Chapter 5 Contivity 1600 Option Installation; need to turn off the Contivity switch if you are only; Removing the Contivity 1600 front bezel; To remove the front bezel you need a Phillips screwdriver.

68 Chapter 5 Contivity 1600 Option Installation 302283-E Rev 00 Removing the Contivity 1600 front bezel You must remove the bezel to insert the recovery diskette. Note that you do not need to turn off the Contivity switch if you are only removing the front bezel. Figure 29 shows you how to remove th...

Page 69 - Removing the Contivity 1600 top cover; To remove the cover you need a Phillips screwdriver.; Removing the Contivity 1600 power cord; You; do; need to turn off the Contivity switch to remove the top

Chapter 5 Contivity 1600 Option Installation 69 Installing Hardware Options for the Contivity VPN Switch Removing the Contivity 1600 top cover To install LAN or WAN cards, or to install additional memory, you must remove the Contivity 1600’s front bezel and then the switch’s top cover. To remove the...

Page 71 - Contivity 1600 system board layout; Contivity 1600 system board

Chapter 5 Contivity 1600 Option Installation 71 Installing Hardware Options for the Contivity VPN Switch Contivity 1600 system board layout Figure 32 shows the Contivity 1600’s system board, in particular the DIMMs, option card slots, and the CPU cooling fan. Figure 32 Contivity 1600 system board Wa...

Page 72 - Installing Contivity 1600 option cards; Remove the power cord, as shown in; Remove the front bezel, as shown in

72 Chapter 5 Contivity 1600 Option Installation 302283-E Rev 00 Installing Contivity 1600 option cards This section shows you how to install LAN or WAN option cards in the Contivity 1600. 1 Turn off the switch. 2 Remove the power cord, as shown in Figure 33 . Figure 33 Removing the Contivity 1600 po...

Page 73 - Remove the top cover, as shown in; Installing Contivity 1600 LAN/WAN option cards; Slide the option card into the intended slot, as shown in

Chapter 5 Contivity 1600 Option Installation 73 Installing Hardware Options for the Contivity VPN Switch 4 Remove the top cover, as shown in Figure 31 . 5 Remove the filler panel screw and pull out the filler panel, as shown in Figure 34 . Figure 34 Installing Contivity 1600 LAN/WAN option cards 6 S...

Page 74 - Replace the card and screw.

74 Chapter 5 Contivity 1600 Option Installation 302283-E Rev 00 Figure 35 Installing Contivity 1600 option cards 7 Replace the card and screw. 8 Replace the top cover. 9 Replace the front bezel. 10 Reconnect the power cord. 11 Turn on the switch. Option card Motherboard Option card slot CS160019A

Page 75 - shows you how to unlock a DIMM and remove or install the DIMM in; Installing Contivity 1600 DIMMs

Chapter 5 Contivity 1600 Option Installation 75 Installing Hardware Options for the Contivity VPN Switch Installing Contivity 1600 DIMMs Figure 36 shows you how to unlock a DIMM and remove or install the DIMM in the next available slot (for example, if the DIMM # 1 slot is populated, than add the ne...

Page 78 - Chapter 6 Contivity 600 Option Installation; Reconnect the power cord to turn the switch back on.; Opening the Contivity 600; Turn the switch over to see the bottom of the box.

78 Chapter 6 Contivity 600 Option Installation 302283-E Rev 00 9 Reconnect the power cord to turn the switch back on. Opening the Contivity 600 To access the system, you must remove remove all cables, the power cord, and the bottom metal screws and pull the chassis from the rear. You need a Phillips...

Page 79 - shows how to remove the system

Chapter 6 Contivity 600 Option Installation 79 Installing Hardware Options for the Contivity VPN Switch Figure 37 Removing the bottom screws 4 Firmly pull the chassis towards you to loosen it from the casing. You can gently shake it so that it slips outwards and into your hand or you can pull gently...

Page 80 - Contivity 600 system board layout

80 Chapter 6 Contivity 600 Option Installation 302283-E Rev 00 Figure 38 Removing the system from the chassis l Contivity 600 system board layout Figure 39 shows the Contivity 600 system board, in particular the option card slot, DIMM memory, and the CPU cooling fan. CS60004A I/O EXPANSION BAY CONSO...

Page 81 - Installing Contivity 600 option cards

Chapter 6 Contivity 600 Option Installation 81 Installing Hardware Options for the Contivity VPN Switch Figure 39 Contivity 600 system board Installing Contivity 600 option cards This section shows you how to install LAN or WAN option cards in the Contivity 600. Warning: Beware of danger if the batt...