NEC XT4100 - Manuals - manualsarea.com

Page 2 - High Light Output Projection System; User’s Manual

XT5100/XT4100 High Light Output Projection System User’s Manual

Page 3 - E – ii; GSGV Acoustic Noise Information Ordinance:; CAUTION; RISK OF ELECTRIC SHOCK; DO NOT OPEN; RISQUE D’ELECTROCUTION; NE PAS OUVRIR; ATTENTION; WARNING

E – ii CAUTION: To turn off main power, be sure to remove the plug from power outlet. The power outlet socket should be installed as near tothe equipment as possible, and should be easily accessible. 3. GSGV Acoustic Noise Information Ordinance: The sound pressure level is less than 70 dB(A) accordi...

Page 4 - E – iii; Important Safeguards

E – iii Fire and Shock Precautions 1. Ensure that there is sufficient ventilation and that vents are unob- structed to prevent potentially dangerous concentrations of ozoneand the build-up of heat inside your projector. Allow at least 8 inches(20cm) of space between your projector and a wall. Allow ...

Page 5 - E – iv; Recommandations importantes

E – iv Précautions contre l'incendie ou la décharge 1. S'assurer qu'il y ait une ventilation suffisante et que les ouvertures n e s o i e n t p a s o b s t r u é e s a f i n d ' é v i t e r d e s c o n c e n t r a t i o n spotentiellement dangereuses d'ozone et l'accumulation de chaleur àl'intérieur...

Page 6 - E – v; LIMITED WARRANTY

E – v LIMITATION OF IMPLIED WARRANTIES All implied warranties, including warranties of merchantability and fit-ness for a particular purpose, are limited in duration to the length ofthis warranty. EXCLUSION OF DAMAGES NECTECH’s liability for any defective product is limited to the repair orreplaceme...

Page 7 - E – vi; TABLE OF CONTENTS; INTRODUCTION

E – vi TABLE OF CONTENTS Video Adj ........................................................................ E-31 Noise Reduction ...................................................... E-31Color Matrix ............................................................. E-32Y/C Delay ..........................

Page 8 - Getting Started

E – 1 Getting Started The fastest way to get started is to take your time and do everythingright the first time. Taking a few minutes now to review the manual maysave you hours later on. At the beginning of each section of the manualyou'll find an overview. If the section doesn't apply, you can skip...

Page 9 - Part Names and Functions

E – 2 1. Part Names and Functions Stacking Pad (4 pcs) Digital Input Terminal Panel Remote Sensor PC Card Slot Insert a PC memorycard here to upgradethe projector systemsoftware or copydata Lens (Optional) Input Terminal Panel Ventilation (in) Foot Release Lever (both sides) Ventilation (out) * To t...

Page 10 - Controls

E – 3 LENS SHIFT ZOOM MENU SELECT - + ENTER ON INDICATOR POWER STATUS ON/OFF OFF CANCEL FOCUS 11 10 9 8 7 5 4 2 1 3 6 1. Power Button Press to turn the projector on when the projector is in the standby con-dition (Main Power switch must be on and the POWER indicator lit or-ange). Press and hold for ...

Page 11 - Terminal Panel

E – 4 Terminal Panel INPUT3 RGB R/Cr G/Y B/Cb H/HV V R/Cr Cr Y G/Y B/Cb Cb H/HV V OPTION IN OUT REMOTE1 REMOTE2 INPUT7 INPUT8 INPUT5 S-VIDEO1 Y C S-VIDEO2 VIDEO1 VIDEO2 INPUT6 IN OUT INPUT2 INPUT1 INPUT4 5 6 1 2 3 4 9 10 8 7 1. INPUT 3 RGB Connector (Mini D-Sub 15 pin) Connect your PC or other analo...

Page 13 - Remote Control

E – 6 Remote Control 1 POWER ON Press to turn on the projector. The POWER indicator lights up green. 2 POWER OFF Press and hold this button for a minimum of two seconds to turn off theprojector. 3 MENU Press to display the main menu.While pressing and holding CTL, press this button to display the Re...

Page 14 - Remote Control Precautions

E – 7 18 MUTE SOUND (available only when using with the ISS -6020 or IPS4000)Turns off the sound for a short period of time. Press again to restore thesound. 19 MUTE OSD Press to turn off the on-screen display. Press again to restore the on-screen display. NOTE: You can also turn off the on-screen d...

Page 15 - Table of Throw Distances and Screen Sizes for Optional Lenses; Throw Distance; Setting Up Your Projector

E – 8 2. INSTALLATION Formulas: Screen width H (m) = Screen Diagonal x 4/5 x 0.0254 Screen height V (m) = Screen Diagonal x 3/5 x 0.0254Screen width H (inch) = Screen size x 4/5Screen height V (inch) = Screen size x 3/5 Diagonal 80" 100" 120" 150" 180" 210" 240" 270" ...

Page 16 - Lens Shift Adjustable Range

E – 9 Lens Shift Adjustable Range Lens Shift Adjustable Range for Desktop and Ceiling Mount ApplicationThe diagram below shows the location of the image position in the lens. The lens can be shifted within the shaded area as shown using the normalprojection position as a starting point. Maximum Poss...

Page 17 - Moving The Projector

E – 10 Pulling Out the HandlesPull out the handle until it clicks into place. Retracting the Handles1) Push the lever to unlock and 2) retract the handle. Selecting A Location The fur ther your projector is from the screen or wall, the larger the im-age. The minimum size the image can be projected i...

Page 18 - Connect the supplied power cable to the projector.; Using the Power Cable Stopper; Lift down the wire stopper to hold the power cable.

E – 11 3. SETUP OFF PO WER ON Connecting the Power Cable and Turn-ing on the Projector Before you turn on your projector, ensure that the computer or videosource is turned on and that your lens cap is removed. 1. Connect the supplied power cable to the projector. Plug the supplied power cable into t...

Page 19 - Set up the projector; control or using the menu.

E – 12 Set up the projector 1. Turn on the projector2. Select your type of projection:Desktop front, ceiling rear, desktop rear, and ceiling front. 3. Display the test pattern by pressing the TEST button on the remote control or using the menu. TEST 4. Adjust the image position and the image size. (...

Page 20 - Keystone

E – 13 Keystone Keystone distortion Normal Keystone is the distortion of a projected image that usually creates awider top than bottom. Aiming a projector upward on a wall rather thanstraight at a wall creates this distor tion. Use the 䊴 or 䊳 buttons on the slide bar to correct this keystone (trapez...

Page 22 - Projector Orientation

E – 15 Projector Orientation An image can be projected from in front or behind a screen, and theprojector can be installed on the ceiling*. Ceiling Front Projection Use [Projector Options] → [Setup] → [Page 1] → [Orientation] to select "Ceiling Front". (See page E-36.) Ceiling Rear Projectio...

Page 23 - When used in standalone operation; Connecting Your PC Or Macintosh Computer

E – 16 When used in standalone operation Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to XT5100/XT4100 Pro-jector will enable you to project your computer's screen image for animpressive presentation. To connect to a PC or Macintosh :1. Turn off the power to your...

Page 25 - How to make connections:

E – 18 When Used with Two or More Switchers(100 Inputs) Up to 100 inputs can be accepted using the NEC ISS-6020 Switcher. How to make connections: 1. Connect the REMOTE 1 terminal of the master Switcher to the RE- MOTE 1 of the projector using the optional control cable (15p-15p/CTL-6010). 2. Next c...

Page 26 - Output to

E – 19 Set the DIP switch (S8601) of the Switcher as follows: The Projector Slot 1 of the Master Slot 2 of the Master Slot 3 of the Master Slot 4 of the Master Slot 5 of the Master Slot 6 of the Master Slot 7 of the Master Slot 8 of the Master Slot 9 of the Master Slot 10 of the Master Master Slave ...

Page 27 - REMOTE 1 Connector

E – 20 REMOTE 1 Connector Pin Configuration of Optional CTL-6010 Cable REMOTE 1 connectorof the Switcher mini D-sub 15 pin (female) REMOTE 1 connector ofthe Projector mini D-sub15 pin (female) Shield (frame ground) Pins without a number are open. 5 1 4 2 3 10 11 12 13 14 15 6 9 7 8 This connector is...

Page 28 - When used in stand alone operation.

E – 21 When used in stand alone operation. Pin No. 14 5 10 4,8,12,11 SHORT/OPEN SHORT OPEN SHORT OPEN SHORT OPEN FUNCTION External control mode ON External control mode OFF POWER ON POWER OFF PICTURE MUTE ON PICTURE MUTE OFF * When the combinations other than specified in the above table are selecte...

Page 29 - Operating Multiple Projectors with Remote Control

E – 22 REMOTE2 INPUT7 S-VIDEO1 Y C IN OUT Operating Multiple Projectors with Remote Control You can operate multiple projectors with the same remote control in wireless operation.To do so: 1. Select [Menu] → [Projector Options] → [Setup] → [Page 5] → [Projector ID] and assign an ID number to each pr...

Page 30 - Using the RGB DIGITAL connectors; Connection for Triple Stacking in Link Mode

E – 23 Using the RGB DIGITAL connectors (XT5100 only) The Link mode function allows you to adjust or set multiple projectors using the RGB DIGITAL and OPTION connectors.The DVI DIGITAL input accepts up to the XGA (1024 x 768 @85Hz) signal. NOTE: The Auto Adjust feature does not work for DVI digital ...

Page 31 - Turn On The Projector

E – 24 Using The Menus 1. Press the MENU button on the remote control to display the menu. 2. Use the ▲ or ▼ button on the remote control to select the sub menu. 3. The right-oriented delta symbol indicates further choices are avail- able. Press the 䊳 button to highlight the item you want to adjust ...

Page 32 - A List of Direct Key Combinations

E – 25 A List of Direct Key Combinations CTL+ INPUT (1-10) Switches to any selected signal found in the Entry List.To enable this combination, you must first assign specific remote keys for direct inputselection in the Entry Edit window. CTL+ ENTER (While displaying Entry list) Displays the Entry Ed...

Page 33 - Menu Tree

E – 26 Menu Tree NTSC, Graphics, Graphics/NTSC, PAL/SECAM2.8, PAL/SECAM, Natural 1/Natural 2 Advanced Menu Source Select Adjust (Source) Ref Adj Factory Default Projector Options PC Card Files Help Test Pattern RGB1 RGB2 RGB3 Component (YCbCr) Video1 Video2 S-Video1 S-Video2 RGB (DIGITAL) SDI Entry ...

Page 35 - Menu Elements

E – 28 Menu windows or dialog boxes typically have the following elements: Title bar: Indicates the menu title. Highlight: Indicates the selected menu or item. Solid triangle: Indicates further choices are available. A highlighted triangle indicates the item is active. Tab: Indicates a group of feat...

Page 36 - Entry List; Swicher

E – 29 Menu Descriptions & FunctionsSource Select Use the SELECT ▲ or ▼ button to select the master slot number from 1 to 10 and then the slave slot number from 1 to 10 on the Select Slotmenu. Select OK and press ENTER.To close the window without storing the settings, select Cancel andpress ENTE...

Page 37 - Picture; White Balance

E – 30 Picture Select "List" and press ENTER to display the direct Key assignmentlist.Select "OK" and press ENTER to close the window.To close the List window, press CANCEL on the remote. Adjust (Source) This option corrects gamma. Select the appropriate item. NTSC .....................

Page 38 - Video Adj

E – 31 Horizontal/Vertical Position (when Auto Adjust is off): Adjusts the image location from left to right.This adjustment is made automatically when the Auto Adjust is turnedon. Aspect Ratio (not available for SXGA) : You can select the aspect ratio for input signal and display area re-spectively...

Page 39 - Option Adj

E – 32 Color Matrix First, select an appropriate color matrix for your input signal, eitherHDTV or SDTV. Then select an appropriate matrix type from B-Y/R-Y, U/V, Cb/Cr, Pb/Pr or IVX. NOTE: The Color Matrix feature is available for component video signal only. Y/C Delay (not available for RGB) Adjus...

Page 40 - Ref Adj; Switcher; Lens Memory

E – 33 Switcher Gain This feature adjusts the input level of the signal. This must be doneto each color:R, G, and B. Volume This feature adjusts the volume of the audio output. Adjust the soundcorresponding to the slot. Ref Adj Keystone This feature corrects the keystone (trapezoidal) distor tion to...

Page 41 - Projector Options; Timer; Lamp; Reference White Balance; Factory Default

E – 34 Projector Options Enables you to set preferences and other operating options. Timer Enables you to turn the projector on or off automatically at a specifiedtime. Two timer functions are available: On/Off Timer and Sleep Timer. [On/Off Timer] Up to eight settings can be programmed. • Before se...

Page 42 - Menu

E – 35 5. To enable your setting, select Active on the Execute Switch. 6. Select OK and press the ENTER button on the remote control to complete the setting. NOTE: When On Timer is set and the projector is in the standby mode, theStatus indicator flashes green to show that On Timer program is active...

Page 43 - Setup

E – 36 Setup Enables you to set operating options.Press "OK" to save your changes for all the features of Page1, Page2,Page3, Page 4 and Page5. [Page 1] Orientation This sets the orientation of the image for your type of projection.The options are: desktop front projection, ceiling rear proj...

Page 44 - Link Mode; Switcher Control

E – 37 Keystone Save This option enables you to save your current keystone settings. Saving your change once affects all sources. The changes are savedwhen you turn off the projector. Lens Memory This function applies the stored lens shift, focus, and zoom adjust-ment values to the selected signal.T...

Page 45 - PC Card Files; Contents; Help; Source Information

E – 38 PC Card Files Displays a list of all the files stored in the PC card so that you canselect a file you want to display. You can also sort files by file nameor date, or display the file.Although a list of all the files in the PC card is displayed, you canview files in idx, text, HTML, JPEG and ...

Page 46 - Test Pattern

E – 39 [Page 4] Link Mode Displaying Current Status of Link ModeWhen selecting the tab "Page 4 ", you will get the following dialogbox. Master ID .................... Indicates the Master projectorStatus ......................... Indicates the status of the master projectorConnected PJ ........

Page 47 - Optical; Electrical

E – 40 6. SPECIFICATIONS Optical Panel * 1 DMD TM .9" x 3 1024 x 768 native resolution up to 1600 x 1200 with advanced AccuBlend TM Technology Lamp 1.0kW Bubble Type Shor t Arc XenonBuilt in: Overheat Protection Lamp Over-Usage Protection Light Output XT5100: 5,000 ANSI lumens (High-Bright mode)...

Page 48 - Mechanical

E – 41 External Control RS232C(1) D-sub 9 pinContact ClosureSwitcher (2) D-sub 15 pin In/Out Addressable Remote Control (wired / wireless) Power Requirement 100-120 / 200-240 VAC, 50/60Hz Input Current 11 A / 7.3 A Power Consumption 1.0 kW / 1.5 KW Mechanical Installation Orientation: Desktop/Front,...

Page 49 - Optional Accessories

E – 42 7. Optional Accessories Lens TL-08SF (Short Focal Lens 0.84) : 10kgTL-1ZH/1Z (Zoom Lens 1.5 - 2.5:1) : 5.5kgTL-2Z (Zoom Lens 2.5 - 4.0:1) : 4.5kgTL-4Z (Zoom Lens 4.0 - 7.0:1) : 4.5kg Interface Board XT SDI BOARDX DIGITAL RGB BOARD Ceiling Mount Kit XT CMKIT Switcher ISS-6020 Video/RGB Switche...

Page 50 - Compatible Input Signal List

E – 43 8. Compatible Input Signal List Compatible Input Signal List NOTE1: The VGA, SVGA, SXGA and UXGA signals are displayed with Advanced AccuBlend.NOTE 2: UXGA can be supported for separate sync signal only.NOTE 3: DVI digital signal can support a maximum resolution of [email protected] 4: Digital si...

Page 51 - List of Menu Items Available on Link Mode

E – 44 List of Menu Items Available on Link Mode 9. Function Link mode Menu Source Select L Adjust(Source) Picture L White Balance L Image Pixel Adjust L Position N Aspect Ratio L Resolution L Overscan L Video Filter L Blanking N Video Adj N Option Adj N Lens Memory N Switcher N Ref Adj Keystone N L...

Page 52 - Appendix; Dimensions

E – 45 Appendix Dimensions 506 (19.92) 326 (12.83) 174 (6.85) 682 (26.85) 35.5 (1.40) 300 (11.81) 30 (1.18) 54 (2.13) The drawings do not include the lens par t. Unit: mm (inch)

Page 53 - Tips on Adjusting Focus for Lens Memory Function

E – 46 Tips on Adjusting Focus for Lens Memory Function Optimum focus for lens memory function can be achieved on the projector by paying special attention in a few areas.Focus adjustment after the projector has warmed up to normal operating temperature is better than doing so when the projector is ...