Page 2 - English; Declaration; Declaration of the Manufacturer; WARNING
English English-1 Declaration Declaration of the Manufacturer TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOTUSE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESSTHE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE ...
Page 3 - Declaration of Conformity; FCC Information
English-2 Declaration of Conformity This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired opera...
Page 4 - Contents
English English-3 MultiSync L CD1860NX Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD1860NX monitor with height adjustable base • Power Cord(s) • Video Signal Cable • User’s Manual • Cable Management Cover • NEC LCD Setup Software, User’s Manual and ot...
Page 5 - Quick Start
English-4 Quick Start To attach the MultiSync LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.1 ). Tighten all scre...
Page 6 - Raise and Lower Monitor Screen
English English-5 Raise and Lower Monitor Screen The monitor may be raised or lowered in either Por trait or Landscape mode.To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height ( Figure RL.1 ). Figure C.1 Figure C.2 Figure D.1 Figure RL.1 INPUT1 I...
Page 8 - Controls; Brightness/Contrast Controls; BRIGHTNESS; Position Controls
English English-7 Controls OSM (On-Screen Manager) control buttons on the front of the monitorfunction as follows: To access OSM menu, press any of the control buttons (EXIT, , , –, +). To change signal input, press the SELECT button. NOTE: OSM must be closed in order to change signal input. NOTE: W...
Page 9 - AccuColor Control Systems (Color Control Systems); Tools 1
English-8 FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. Should the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, afine tuning can be performed using the “Fine” function. It improves fo...
Page 10 - Tools 2
English English-9 Tools 2 Language: OSM control menus are available in seven languages. OSM Position: You can choose where you would like the OSM control image to appear on your screen. Selecting OSM Location allows you to manually adjust the position of the OSM control menu left, right,down or up. ...
Page 11 - Recommended use
English-10 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC LCD COLOUR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable par ts inside and opening or removing covers may expose you to dangero...
Page 13 - Specifications
English-12 Specifications Monitor Specifications LCD1860NX (L182R4) Monitor Notes LCD Module Diagonal: 46 cm/18.1 inches Active matrix; thin film transistor (TFT) liquid Viewable Image Size: 46 cm/18.1 inches crystal display (LCD); 0.28 mm dot pitch; Native Resolution (Pixel Count): 1280 x 1024 200 ...
Page 14 - Features
English English-13 Features ambix Technology: Dual input technology allowing both analog and digital inputs off of one connector (DVI-I) as well as additional legacy analog suppor t off of a traditional 15-pin VGA connector. Provides traditional MultiSync technologycompatibility for analog as well a...
Page 15 - Troubleshooting
English-14 Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Check the Vacation Switch should be in the ON position. • Front Power Switch and computer power switch should be in the ...