NEC SB-L008KU - Manuals - manualsarea.com

Page 2 - Declaration of conformity; For USA; For Canada; Declaration; Declaration of the Manufacturer

2 Declaration of conformity For USA FCC Information 1. Use the attached specified cables with SB-L008KU(L008KU) Media Player so as not to interfere with radio and television reception. (1) Please use a good quality shielded video signal cable. Use of other cables and adapters may cause interference ...

Page 3 - Installation; Caution

3 Installation WARNING: Do not insert foreign objects inside the cabinet during installation. 1 Insert the enclosed SD Memory Card firmly into the Media Player’s memory card connector with the label side facing up. Caution Confirm that the write-protect switch is not at LOCK position. 2 Turn off the...

Page 4 - Contents; • Utility discs; Terminal panel; Connector to connect to the display.; NOTE

4 • Memory card• USB extension cable• Setup guide Contents • Utility discs (Attached Software and User’s Manual) • Component input conversion cable Terminal panel 1 Slot interface Connector to connect to the display. 2 Memory card connector Insert the enclosed memory card. 3 Video input connector Co...

Page 5 - Basic Operation; Selecting Media Player

5 Basic Operation To operate this device, use the remote control enclosed with the display. Selecting Media Player Press the “OPTION” button on the remote. Opening Media Player OSD menu When the input signal of the monitor is “OPTION”, press the “OPTION” button to turn on/off the Media Player OSD. W...

Page 6 - Connection; Preparation; Authoring software; Connection when using USB memory to distribute programs

6 Connection When using LAN, after finishing the “Connection/Setting” in this chapter, refer to the “LAN Connection/Setting” (page 14). Preparation In order to use the Media Player to display the program on the Display, the enclosed authoring software, a computer, and a USB memory(if the program is ...

Page 7 - Connection and setting; Setting the Media Player; Turn on the main power supply of the display.; LANGUAGE setting; Select the language for the OSD menu.; VIDEO OUT; Display settings; Switch the display power OFF and then ON again.

7 Connection and setting (continued) Setting the Media Player 1. Turn on the main power supply of the display. 2. Press the “POWER ON” button of the remote control toswitch the display on. 3. Press the “OPTION” button of the remote control to select“OPTION” for video input. The Media Player will sta...

Page 8 - Power States and Operations; •Power ON; •Power OFF; Note; Possible Operations in Power Modes

8 Power States and Operations •Power ON Press the “POWER ON” button of the remote control. Media Player and the display will turn on at the same time. Note The Media Player takes approximately 1 minute to start up after it is turned on. During the start up, a message stating that there is no signal ...

Page 9 - How to create program data; Preparing content; Create program data using authoring software; File format

9 How to create program data Preparing content First, prepare the content you want to display. CAUTION: Depending on the file, it may not be used. For details, refer to the “Content Specifications.” NOTE: Data created using PowerPoint ® presentation software (*.ppt) can be used on this equipment by ...

Page 10 - Copy the program data on the memory card of the Media Player; Prepare USB memory containing program data.

10 Copy the program data on the memory card of the Media Player 1. Prepare USB memory containing program data. 2. Press the “STANDBY” button of the remote control to switch off the power of the MediaPlayer, and then set the USB memory containing the program into the USB cable extension. NOTE: If the...

Page 11 - OSD

11 Main Menu DATE/TIME NETWORK PREVIEW TIMER LANGUAGEVIDEO OUT MEMORY CARD SLIDE SHOW ADVANCED OSD Sub MenuDateTimeNTP ServerTime ZoneStatic IP/DHCP IP Netmask GatewayDNSMACProxyUpdate Mode from LAN Power-ON/Power-OFF Free Available Delete All Content Files Normal Mode Slide Show Mode Video Repeat M...

Page 12 - Slide Show Mode/Video Repeat Mode; How to set the Slide Show Mode; Select “Slide Show Mode” in the “SLIDE SHOW” item of the OSD menu.; How to set the Video Repeat Mode; Select “Video Repeat Mode” in the “SLIDE SHOW” item of the OSD menu.; How to release the Slide Show Mode/Video Repeat Mode

12 Slide Show Mode/Video Repeat Mode These functions continuously display still image data (*.jpg, *.jpeg, *.png, *.bmp) or movie files (WMV9, MPEG1, MPEG2) in the USBmemory in the order of the file names. The still image data or movie data can be displayed without using authoring software. How to s...

Page 13 - How to create program data using external video

13 How to create program data using external video External video image from the S TERMINAL input connector can be displayed with stillimages and messages. (For details refer to the authoring software UserÅfs Manual.) The following shows the connection with commercially available AV equipment. Progr...

Page 14 - LAN Connection and setting; Introduction; The procedure for LAN setting is as follows.; Media Player LAN setting; Authoring software LAN setting

14 <Using LAN> LAN Connection and setting Introduction When distributing program data via LAN, LAN connection and setting are required. There are two methods for setting the IP Address, one for Static IP Address and one using DHCP servers. In the case of Static IP Address, refer to “LAN connec...

Page 15 - •When connecting directly to a computer

15 <Using LAN> LAN Connection and setting (continued) •When connecting directly to a computer •When connecting with several computers via a hub •When using a DHCP server (built into routers) NOTE: Refer to “LAN connection/setting: Use DHCP servers.” NOTE: A maximum of 20 Media Players can be c...

Page 16 - LAN Connection and setting: When using Static IP Address; Static IP Address setting of the Media Player; Switch on the power of the Media Player and Display.

16 <Using LAN> DATE/TIMENETWORKPREVIEWTIMERLANGUAGEVIDEO OUTMEMORY CARDSLIDE SHOWADVANCED Static IP IP: 192 .168 .0 .2 Netmask: 255 .255 .255 .0Gateway: 192 .168 .0 .1 DNS: 0 .0 .0 .0 MAC: 00:50:41:80:02:A9 Proxy Update Mode from LAN: Push mode Pull mode Apply LAN Connection and setting: When ...

Page 17 - Authoring software panel registration; LAN connection test; Confirm that the setting screen is displayed.

17 <Using LAN> LAN Connection and setting: When using Static IP Address (continued) 2. Authoring software panel registration Click the panel setting button in the “Panel Control” menu of theauthoring software. 1 Distribution list setting If no changes are required, click “Next.” 2 Set to LAN (...

Page 18 - LAN Connection and setting: When using the DHCP server; Set the Media Player to DHCP mode.; Set the OSD screen as shown below.; Confirm and set the Media Player name; Confirm that the computer’s IP Address is set.

18 <Using LAN> DHCP IP: 192 .168 .0 .3 Netmask: 255 .255 .255 .0 Gateway: 192 .168 .0 .1 DNS: 192 .168 .0 .1 MAC: 00:50:41:80:01:34 Proxy Update Mode from LAN: Push mode Pull mode DATE/TIMENETWORKPREVIEWTIMERLANGUAGEVIDEO OUTMEMORY CARDSLIDE SHOWADVANCED Apply LAN Connection and setting: When ...

Page 19 - LAN Connection and setting: When using DHCP server; Keep a memo of the Media Player name.

19 <Using LAN> LAN Connection and setting: When using DHCP server (continued1) 6) After displaying the setting screen, confirm theMedia Player name (player Name). To change the name, click the Change Player Namebutton, input the name using 15 or less one-bytecharacters starting with an alphabe...

Page 20 - LAN Connection and setting: When using a DHCP server

20 <Using LAN> LAN Connection and setting: When using a DHCP server (continued 2) 4. LAN connection test 1) Startup Internet Explorer on the computer, input the MediaPlayer name set in the authoring software in the address columnafter the “http://.” NOTE: The uppercase and lowercase alphabets ...

Page 21 - Distribute program data to the Media Player; Use authoring software to create a program.

21 <Using LAN> Content Updating... Please do not power-off. Distribute program data to the Media Player 1. Use authoring software to create a program. Refer to the “SB-L008KU Quick Reference Guide” on the enclosed CD-ROM. 2. Switch on the power to the devices on the network such as Media Playe...

Page 25 - Troubleshooting; (Using Ping command to conduct a LAN connection test); In the case of a Static IP Address; Command prompt screen

25 Troubleshooting (Using Ping command to conduct a LAN connection test) If the data cannot be distributed via LAN, use the Ping command on the computer to conduct a LAN connection test. In the case of a Static IP Address 1 Look up the IP Address in “NETWORK” on the OSD. 2 Startup the command prompt...

Page 27 - Specifications; SB-L008KU Media Player compatible displays; Authoring software specifications

27 Specifications SB-L008KU Media Player compatible displays P401, P461, M401, M406, P521, X431BT, P701 Media Player (SB-L008KU) Specifications *Note1) Programs using external video images cannot be output to the DVI output connector. They can only be output to the display which this device is conne...

Page 28 - Content Specifications

28 Specifications (continued) Content Specifications (1) Movie file •Codec Windows Media Video 9 (WMV3) •Bit rate Normal resolution (Up to 720 x 480): maximum 20 MbpsHigh-resolution (1920 x 1080 or 1280 x 720): maximum 35 Mbps •maximum resolution 1920 x 1080 25p (progressive)1280 x 720 30p (progress...

Page 30 - Software license information

30 Software license information This product contains open source software. For the use conditions of the open source software, refer to the following. Also, refer to the officialwebsite of each open source software. GNU Lesser General Public License (“GNU LGPL”): (“Software license information.pdf”...